What are torque specifications for Chevy axle nut?
2012-2017 There are two types of wheel drive shaft nuts, both of which have different tightening torque specifications. Check the style nut that is on the vehicle when staking the nut. Style 1 nut has the thin collar (1.5 mm) thickness. Style 2 nut has the thick collar (2.7 mm) thickness.
How big is the axle nut on a Chevrolet Acadia?
Make and Model > Chevrolet > Acadia > Chevrolet Axle Nut Torque… AWD 2007-2016 FRONT 173/235-ft/lbs/Nm REAR 151/205-ft/lbs/Nm 2017 FRONT AND REAR Use new nut. Tighten to 111 ft-lbs/150 Nm. Loosen 45° then retighten to 199 ft-lbs/270 Nm. 2017 Use new nut. Tighten to 111 ft-lbs/150 Nm. Loosen 45° then retighten to 199 ft-lbs/270 Nm.
How big is the axle nut on a Chevy Malibu?
2013-2017 Tighten in three steps: First, 111 ft-lbs/150 Nm; second, loosen 45 degrees; last, tighten 185 ft-lbs/250 Nm. Malibu Limited 2016 Tighten to 111 ft-lbs/150 Nm. Back off 45 degrees and retighten to 184 ft-lbs/250 Nm. 2013-2015 177/240-ft/lbs/Nm Use new original equipment nut.
2012-2017 There are two types of wheel drive shaft nuts, both of which have different tightening torque specifications. Check the style nut that is on the vehicle when staking the nut. Style 1 nut has the thin collar (1.5 mm) thickness. Style 2 nut has the thick collar (2.7 mm) thickness.
How big is the axle nut socket on an Acura?
Acura Axle Nut Torque Specification Socket Size. Acura Axle Nut Torque Specification and Socket Size. Acura C, CL Axle Nut Torque and Socket 36mm. 2.2L, 2.3L, 3.0L FRONT 1997-1999 134/182 -Ft/NM REAR 181/245 -Ft/NM. 3.2 2001-2003 FRONT 181/245 -Ft/NM.
Where can I find the torque specification guide?
Ensure that you have the correct torque for the application by referring to SKF 457377 torque specification guide or contact the vehicle manufactures dealer. It is important that you properly torque the spindle nut to ensure optimum bearing life. Under torque of an axle nut will allow excessive movement causing uneven loading and excessive wear.
What happens if your spindle nut is over torque?
It will also leave your spindle nut under or over torque resulting in hub assembly failure. Ensure that you have the correct torque for the application by referring to SKF 457377 torque specification guide or contact the vehicle manufactures dealer. It is important that you properly torque the spindle nut to ensure optimum bearing life.
How much torque is need on my wheel axle hub nut?
Tighten the axle nut with a socket and torque wrench; torque the axle nut between 15 to 20-ft pounds of torque to preload the axle bearings. Rotate the hub eight to 10 revolutions by hand to fully seat the bearing races. Loosen the axle nut until it is freely loose, then finger-tighten the axle nut.
What is the wheel lug nut torque?
Wheel Lug Torquing. (Lea en español) Proper wheel installation requires the wheel-attaching hardware (lug nuts or bolts) be tightened to the recommended torque specification for the vehicle make, model and year. Torque specifications are usually found in the vehicle’s owner’s manual.*. Proper torque requires using the correct tools, procedures and patterns.
What are torque specifications?
Torque specifications are for dry threads only. The fastener threads should be free of oil, dirt, grit, corrosion, etc. The hardware should turn freely without binding when tightened by hand. It is important NOT to lubricate hardware threads or seats. The friction at which torque is measured against should come from the hardware seats.
It will also leave your spindle nut under or over torque resulting in hub assembly failure. Ensure that you have the correct torque for the application by referring to SKF 457377 torque specification guide or contact the vehicle manufactures dealer. It is important that you properly torque the spindle nut to ensure optimum bearing life.
How big is the axle nut on a Cadillac?
Tang on ring must press through slot on spindle. Hole in pin must align with locknut. Turn adjusting nut to align. Endplay should be .001- .010″. With automatic locking hubs tighten adjusting nut to 50 ft-lbs/68 Nm while turning hub.
What should the torque be on a U-bolt?
U-Bolts that have been well lubricated with an anti-seize compound will have a torque range between plated and unplated values. All the above values are general guidelines. The OEM Service Manual on specific models always takes precedence over values shown. Snug U-Bolts in the seqence shown. Tighten completely in the sequence shown. MAX. TORQUE
Can a calibrated torque wrench install an axle?
Use a qualified, calibrated torque wrench. Do not use an impact gun to install the axle nut. The impact gun will damage the axle nut. It will also leave your spindle nut under or over torque resulting in hub assembly failure.
Can a impact gun damage an axle nut?
The impact gun will damage the axle nut. It will also leave your spindle nut under or over torque resulting in hub assembly failure. Ensure that you have the correct torque for the application by referring to SKF 457377 torque specification guide or contact the vehicle manufactures dealer.