When does the fault code flash on an Eaton transmission?
Turn the key off and on 4 times within five seconds ending with the key in the on position. After 5 seconds, the Service light begins flashing two-digit fault codes. If no faults are active, the service light will flash code 25 (no codes). Two digit fault codes will be displayed in the gear display.
How to troubleshoot an Eaton heavy duty transmission?
Guide to servicing and repairing Eaton Fuller heavy-duty truck transmission, assistance locating the issue of transmission trouble, analyze the cause and make necessary repairs for 7, 8, 9, 10, 13, 15 and 18 speed Eaton transmissions. For more in-depth assistance refer to your transmission model service manual or give us a call at 877-776-4600.
When did the Eaton ultrashift 10 speed come out?
Discussion in ‘ Trucks [ Eighteen Wheelers ] ‘ started by giannid, May 16, 2018 . We’ve got a 2010 International 8600 with an Eaton Ultrashift 10 speed.
How to troubleshoot an Eaton ultrashift plus fault code?
When troubleshooting an Inactive fault code, use the Fault Isolation Procedures to guide you to the wiring and connectors associated wi th that fault. Once PD Mode is activated, flex the wiring harness and connectors to attempt to recreate the fault.
How do you retrieve a Eaton Fuller fault code?
After 5 seconds, the Service light begins flashing two-digit fault codes. If no faults are active, the service light will flash code 25 (no codes). To Retrieve Inactive Codes: Turn key on. Turn the key off and on 4 times within five seconds ending with the key in the on position.
What does 88 stand for in Eaton transmission?
Perform two key clicks of the ignition switch starting with the key on, and ending with the key on. Note: An “88” may show up in the dash at key on, which is a normal power-up test of the display. The gear display will flash a solid “PD” (Product Diagnostic Mode) and the mode will be activated.
What kind of transmission does a Freightliner have?
I have an Eaton 10-speed autoshift transmission and a Detroit engine in my 2001 Freightliner. I am having problems with the transmission. Some times it will not downshift below the 6th gear. It happened 4 times when I was driving a 160 miles trip.
What kind of transmission does an Eaton have?
It just stays in hi and will not downshift to any gear below the 6th. It always work fine again after I turn the engine off and wait about 15 minuts. The transmission is a 10-speed Eaton Fuller Autoshift. Technician: Buddy, Technician replied 11 years ago
What can Autoshift do to make a shift faster?
AutoShift can activate the engine brake to make shifts faster. This can happen even if-the engine brake dash switch is off. If a shift is required while in cruise, AutoShift will interrupt cruise while performing the shift and automatically re-engage cruise after the shift is complete.
What to do if there is an inactive code on your transmission?
If there are inactive codes PD (Product Diagnostic mode) will be displayed. The vehicle will not start in PD mode. You must turn vehicle key OFF and allow the system to power down to exit PD mode before restarting. To start engine turn key off and wait for the transmission to power down. 5.
How long does it take for a fault code to flash?
After 5 seconds, the Service light begins flashing two-digit fault codes. If no faults are active, the service light will flash code 25 (no codes). Two digit fault codes will be displayed in the gear display.
What is the code for a transmission failure?
These codes all relate to shift solenoid failure. Your TCM tells your transmission how and when to shift by opening one of these solenoids to allow transmission fluid to pass into the transmission’s hydraulic control section for the specific gear.
When to use fault code retrieval / clearing automated transmissions?
Fault Code Retrieval/Clearing An 88 may appear in the gear display which indicates self testing. *This code only set inactive. Driving Tips The clutch is only needed at Start-up, when selecting a starting gear, and when stopping. “D”, “M”and “L” can be selected at any speed.
What happens when Autoshift detects a fault?
This can happen even if-the engine brake dash switch is off. If a shift is required while in cruise, AutoShift will interrupt cruise while performing the shift and automatically re-engage cruise after the shift is complete. If AutoShift has detected a fault in the system you will see an “F” in the gear display.
How to get a fault code for an automatic transmission?
1. Turn key “Off” and let transmission power down for at least 5 minutes. 2. Release parking brake and hold vehicle by using the brake pedal. 3. Depress clutch pedal but DO NOTpush it all the way to floor making contact with the clutch brake. 4. Make sure shifter is in neutral. 5. Turn ignition key “On”. 6.
Where can I find the Mercedes Fault codes?
Mercedes MBE codes Page 13 Cummins ISB, ISC codes Page 27 Caterpillar 3126, C7 codes Page 31 EPA 2010 Products: J1939 Fault Codes Retrieving J1939 fault codes HDX/EFX Page 36 Retrieving J1939 fault codes C2 Page 39 Cummins codes Page 41 Allison Trans 2000 codes Page 81