How to bypass PassLock security on a 2003 Oldsmobile Alero?
It will get under your skin really bad the third time, and after that, you will start kicking the dash and swearing. The menu to the left will guide you through the steps necessary to bypass the Passlock Security System on a 2003 Oldsmobile Alero, and keep the “SECURITY” light off forever.
Why is the security light on on my Oldsmobile Alero?
You are driving along, and for no apparent reason, the “SECURITY”light comes on solid and stays on. After you shut down your vehicle, the next time you start your car the SECURITY light is on solid. This is a common problem on the following GM Cars 1999 – 2004 Oldsmobile Alero 1997 – 2003 Chevrolet Malibu 1999 – 2004 Pontiac Grand Am
How to turn off GM PassLock security Telltale?
Here it is in it’s entirity. Turn ON the ignition, with the engine OFF. Attempt to start the engine, then release the key to ON (vehicle will not start). Observe the SECURITY telltale, after approximately 10 minutes the telltale will turn OFF. Turn OFF the ignition, and wait 5 seconds .
How to bypass the PassLock sensor on a 2002 Pontiac Grand Am?
This web page will guide you through the steps necessary to bypass the “Passlock Sensor” on a 2002 Pontiac Grand Am, and keep the “SECURITY” light off forever. The steps necessary are similar on the other models listed above. There are generally only minor differences in how to get the radio out to get to the wires.
It will get under your skin really bad the third time, and after that, you will start kicking the dash and swearing. The menu to the left will guide you through the steps necessary to bypass the Passlock Security System on a 2003 Oldsmobile Alero, and keep the “SECURITY” light off forever.
Why does my Oldsmobile Alero not start?
The passlock sensor in the ignition lock cylinder may fail causing an anti-theft system fault and a no start condition. Our technicians tell us that the ignition lock cylinder should be replace to correct this condition. The average cost for a Oldsmobile Alero No Start Diagnosis is between $88 -$111.
Here it is in it’s entirity. Turn ON the ignition, with the engine OFF. Attempt to start the engine, then release the key to ON (vehicle will not start). Observe the SECURITY telltale, after approximately 10 minutes the telltale will turn OFF. Turn OFF the ignition, and wait 5 seconds .
How long does it take to turn off PassLock sensor?
Observe the SECURITY telltale, after approximately 10 minutes the telltale will turn OFF The vehicle learns the Passlock™ Sensor Data Code and/or password on the next ignition switch transition from OFF to Crank. You must turn the ignition OFF before attempting to start the vehicle.
What to do if your PassLock light does not turn on?
Insert the Key into the ignition switch and try to start the car. It should start, and then stall, with the “SECURITY” light flashing. (In rare cases, the car may keep running and the security light will not illuminate, but that only happens if you are very lucky.)
How to reset the security system in Oldsmobile Aleros?
Rotate the key to the “On” position. Leave the key in that position for 10 minutes. Rotate the key to the “Off” position when the security warning light on the instrument panel disappears. This usually takes 10 to 12 minutes with key in the “On” position. Start the car as normal.
What’s the best way to start an Oldsmobile Alero?
Leave the key in that position for 10 minutes. Rotate the key to the “Off” position when the security warning light on the instrument panel disappears. This usually takes 10 to 12 minutes with key in the “On” position. Start the car as normal. “Haynes Repair Manual: Oldsmobile Alero 1999 thru 2004”; John H. Haynes and Jay Storer; 2005
How to reset PassLock reset system on Chevy?
1. Turn the key to ON and attempt to start the engine and release the key to the ON position. 2. The SECURITY light will illuminate. Wait 10 minutes until it turns off. 3. Turn the key to OFF for 10 seconds. 4. Turn the key to ON and attempt to start the engine.
How do I Turn Off the PassLock security light?
1. Turn the key to ON and attempt to start the engine and release the key to the ON position. 2. The SECURITY light will illuminate. Wait 10 minutes until it turns off. 3. Turn the key to OFF for 10 seconds. 4. Turn the key to ON and attempt to start the engine. If it starts and run, the system has reset.