What does trouble code p2135 OBD-2 mean?

This particular trouble code indicates that the Power Control Module (PCM) has detected an erroneous reading regarding the voltages transmitted by throttle position sensor A or B, the accelerator pedal position sensor and or the actual throttle plate.

What’s the p2135 code on my pigtail truck?

2007 F150 4.2 V6 replaced spark plugs, wires, coil, computer. thottle body, pigtail now get code P2135 engine lite comes on and the truck goes into limp mode. I can clear by tune off the engine, disconnecting the battery, usually fix it but problem keeps coming back. any input – thanks…

What causes the 2135 code on a PCM?

What causes the 2135 code? 1 Faulty PCM 2 Faulty throttle position sensor (s) 3 Faulty accelerator position sensor 4 Disruption in the throttle position sensor circuit such as an open, corrosion, short, damaged wiring or broken electrical connections

Is the p2138 code the same for all commodores?

It is considered generic because it applies to all makes and models of vehicles (1996-newer), although specific repair steps may be slightly different depending on the model.

When does DTC p2135 set in the PCM?

The two TPS sensors operate inversely — one has an increasing voltage when throttle is applied and one has decreasing voltage on throttle application. If the two TPS sensor readings don’t correlate in the PCM for more than a couple seconds, DTC P2135 is set in the PCM. What are the common causes of code P2135? What are the symptoms of code P2135?

What does the p2135 Ford app sensor mean?

P2135 FORD Meaning The Accelerator Pedal Position (APP) sensor is an input to the Powertrain Control Module (PCM) and used to determine the amount of torque requested by the operator. There are 2 pedal position signals in the sensor.

What does the code p0031 mean on a Nissan?

Check for damaged components and look for broken, bent, pushed out, or corroded terminals. The code means that there is a problem with the heater element circuit of the heated oxygen sensor. Water getting inside the heated oxygen sensor connector can caused the heated oxygen sensor fuse to blow, which is a very common problem for this type codes.

What is the diagnostic code for a Nissan check engine light?

Follow scan tool manufacturer’s operating instructions to access the Diagnostic Trouble Codes (DTC’s). Remember, these are manufacturer specific codes only. Refer to our Generic OBD II code listfor definitions on all other Nissan diagnostic trouble codes. Manufacturer Specific Codes P1105MAP/BARO Pressure Switch Solenoid Valve

What to look for in Nissan p2135 code?

Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost to diagnose the P2135 NISSAN code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.

What does p2135 Nissan throttle control actuator mean?

P2135 NISSAN Meaning Electric Throttle Control Actuator consists of throttle control motor, throttle position sensor, etc. The throttle position sensor responds to the throttle valve movement. The throttle position sensor has the two sensors.

When is the p2135 code set on the ECM?

The code P2135 is set when the and incorrect voltage is sent to the Engine Control Module (ECM) compared with the signals from Throttle Position (TP) sensor 1 and Throttle Position (TP) sensor 2.

What does p2135 mean on a Nissan Leaf?

The code P2135 is set when the and incorrect voltage is sent to the Engine Control Module (ECM) compared with the signals from Throttle Position (TP) sensor 1 and Throttle Position (TP) sensor 2

What are the possible causes of a Nissan p2135?

P2135 NISSAN Possible Causes 1 Faulty Electric Throttle Control Actuator (TP sensor 1 and 2) 2 Electric Throttle Control Actuator harness is open or shorted 3 Electric Throttle Control Actuator circuit poor connection 4 Faulty Accelerator Pedal Position Sensor

What does the p2135 code on a computer mean?

The computer monitors the correlation of both voltages. When both voltages agree, the system is functioning properly. When they deviate for two seconds, the code P2135 is set indicating a malfunction somewhere in the system. Additional trouble codes may accompany this code which further identify the problem.

What does the p2135 GMC throttle position sensor mean?

P2135 GMC Meaning The throttle Position (TP) sensors 1 and 2 are potentiometer type sensors each with 3 circuits. – A 5 – volt reference circuit. – A low reference circuit. – A signal circuit The TP sensors are used to determine the throttle plate angle for various engine management systems.

What are the possible causes of a p2135 Chevrolet?

P2135 Chevrolet Possible Causes. Faulty electric throttle control actuator (TP sensor 1 and 2) Throttle Position Sensor harness is open or shorted. Throttle Position Sensor circuit poor connection. Faulty accelerator pedal position sensor.

When to set the TAC code p2135?

A typical TAC system has two TP sensors and two APP sensors for fail-safe reasons. If the data between one of the sensor pairs (e.g, the two throttle position sensors) does not correlate, code P2135 is set. In most cases, the ECM will also force the vehicle into Reduced Power Mode.

Why does my car keep throwing the p0121 code?

Haven’t had many issues with this car, it threw the p0121 first, then a couple days later, today, threw p2135. The way I’m thinking, having both these codes show up is pointing to my pedal position sensor being faulty. Im thinking the p2135 boils down to the pedal position and throttle position sen…

Why do I get error code p2135 on my TPS?

While the error code P2135 might be frustrating, you are likely to be more annoyed by the number of reasons this code appeared in the first place. Unfortunately, diagnosing the issue is not so cut and dry because of the variety of potential culprits.

Where is the OBD code p2135 located?

OBD-II Code P2135 is defined as a Throttle/Pedal Position Sensor/Switch “A”/”B” Voltage Correlation. The Throttle Position Sensor/Switch is located on the Throttle Body of the Intake Manifold and the Pedal Position Sensor/Switch is part of the Accelerator Pedal assembly.

What does p2135 mean on the ECM?

If the data between one of the sensor pairs (e.g, the two throttle position sensors) does not correlate, code P2135 is set. In most cases, the ECM will also force the vehicle into Reduced Power Mode. Users have reported p2135 for the following makes: Chevrolet, Nissan, Ford, GMC, and Suzuki.

What does reduced power code p2138 stand for?

The P2138 Reduced Power bulletin applies to the following vehicles: 2005-2011 GM Passenger Cars and Light Duty Trucks (Including Saturn) The P2128 trouble code refers to Accelerator Pedal Position (APP) Sensor 1-2 Correlation.

What causes reduced power message and trouble code p0106?

Do NOT do that until you have read the rest of this bulletin. A common cause of the reduced power message and trouble codes P0106, P0651, and P2135 is a wire chaffing issue that shorts the reference voltage to ground and prevents the PCM from getting accurate sensor data from the MAP and accelerator pedal positon sensor.

What does p2119 mean on a powertrain control module?

P2119 code definition. What the P2119 code means. This code indicates that the throttle valve is not in the position the PCM (Powertrain Control Module) expects it to be in.

Where is the accelerator pedal sensor on the p2138?

You may also see a P2138 Accelerator pedal position (APP) Sensor 1-2 correlation trouble code. GM says this issue can be caused by water leaking into the instrument panel body harness connector. This connector is located in or near the left hand kick panel or inside the instrument panel, depending on the year and model.

It is considered generic because it applies to all makes and models of vehicles (1996-newer), although specific repair steps may be slightly different depending on the model.

Navigation