When to use the code SPN 1569 fmi31?
SPN 1569 FMI 31 – SCR Tamperproof Warning & Protection System Inducement Severe Fault Overview Fault sets when any aftertreatment sensor or actuator is Open, disconnected, or bad Urea quality is detected for at least one hour.
What is the SPN code for the fuel filter?
SPN Code: SPN Name: SPN Description: 16: Engine Fuel Filter Differential Pressure (see also SPN 1382) Differential pressure measured across the fuel filter located between the fuel tank and the supply pump. See SPN 1382 and Figures SPN16_A & SPN16_B. 18: Engine Fuel Pressure (Extended Range) 19: Engine Oil Pressure (Extended Range) 20
Where to find SPN code for 16 engine?
SPN codes description SPN Code SPN Name SPN Description 16 Engine Fuel Filter Differential Pressure (see also SPN 1382) Differential pressure measured across the fuel filter located between the fuel tank and the supply pump. See SPN 1382 and Figures SPN16_A & SPN16_B.
Which is the correct SPN 91 or 974?
NOTE—See SPNs 91 and 974 for additional accelerator position parameters. 30 Engine Crankcase Blowby Pressure 31 Transmission Range Position Not referenced in J1939-71 32 Transmission Splitter Position The current position of the splitter cylinder. 33 Clutch Cylinder Position Not referenced in J1939-71 36 Clutch Plates Not referenced in J1939-71 37
What is the SPN on a 2016 NH9?
I have a 2016 International NH9 motor. Has only code spn 1569 fmi 31. I can not get any other codes off it. How do I reset this? What do I do its in derate but shows no other codes.
What does SPN 1569 mean on a Cummins Engine?
Spn 1569 relates engine protection torque derate -condition exists. critical fault codes related to engine operation are active code 1 means urgent attention A sort of limp mode setting that requires immediate attention by a cummins service center to prevent further damage to the engine
What is the engine derate code for FMI 31?
This one was MID178 PID118 FMI 1. -the engine derate code of SPN1569 FMI 31 translates to Cummins code 3714 which is indeed an engine derate warning. Strange thing is that derat code should not set without another code setting and showing up at the same time to indicate what caused the derate.
What is the SPN code for a FMI Sid?
SPN FMI PID/SID PID/SID ID FLASH CODE FAULT DESCRIPTION 634 4 SID 40 1321 Constant Throttle Valve Circuit Failed Low 634 3 SID 40 1321 Constant Throttle Valve Circuit Failed High 634 5 SID 40 1321 Constant Throttle Valve Circuit Failed Open 636 1 SID 21 1235 Crankshaft Position Sensor Signal Voltage Too Low
What does SPN 3720 / FMI 15 stand for?
141.1 SPN 3720/FMI 15 This fault indicates that the Diesel Particulate Filter (DPF) has reached the end of its service life and must be replaced. Replace DPF and perform Ash Accumulator reset using DDDL. The DPF lamp will illuminate and SPN 3720/FMI 15 will log when the truck reaches the appropriate mileage interval.
What does SPN stand for on a body controller?
DEFINITIONS •“SPN” represents the Suspect Parameter Number. This number identifies the item for which diagnostics are being reported. •“FMI” is the Failure Mode Indicator. This number represents the type of failure detected. Refer to Failure Mode Indicators (FMI) below for more information. 2 BODY CONTROLLER DIAGNOSTIC TROUBLE CODES (S08327)
When does the malfunction indicator lamp ( MIL ) illuminate?
Malfunction Indicator Lamp (MIL) will illuminate when this fault is detected during two consecutive drive cycles. This fault is a notification indicating SCR Tamperproof Warning and Protection Inducement is in effect. This fault is a notification indicating SCR Tamperproof Warning and Protection Inducement is in effect.
What is the code for the 7600 Vin?
Has the following codes: SPN 3216 FMI 4 SPN 3216 FMI 20 SPN 1569 FMI 31 Seems to be related to the SCR. What is best approach. … read more
What does FMI stand for in failure mode?
FMI” is the Failure Mode Indicator. This number represents the type of failure detected. Refer to Failure Mode Indicators (FMI) below for more information. Active” or “Previously Active” will be displayed to identify whether a fault is currently active or if the fault was previously active.
Who are the satisfied customers of SPN 3362 fmi31?
Satisfied Customers:4,361 Experience: ASE Med/HD Truck Technician, NATEF Diesel Engines and Electrical/Electronics Technician, Network Engineer specializing in CAN faults, Aftertertreatment, and vehicle communications Verified My name is XXXXX XXXXX I will assist you.
What does the source address mean in FMI?
This number represents the number of times a fault has gone from previously active to active. • ³SA´ is the Source Address. This number identif es the module reporting the fault. Refer to Source Addresses (SA) for more information. 3.1. FAILURE MODE INDICATORS (FMI)