Why is there no brake pedal on my new car?

A “no brake pedal” condition can be encountered after a new master cylinder is installed, leading the technician to believe that the master cylinder is defective. This is likely not the case; the condition can be caused by the piston sticking in bore of the master cylinder during the bleeding process when the brake system is manually bled.

What kind of brakes does a Chevy Duramax have?

2004 lb7 Cali. emissions ECLB 2500 HD. Tows 12K lb. 5th wheel. Injectors replaced at 49K miles (Jan. 2012). Fumoto drain valve and stainless bleeder screw from Merchant. Bilstein 5100’s from Norcal Nick.

How did I Fix my Chevy Duramax soft brakes?

I managed to borrow the correct puller to get the pulley off (and back on) picked up a replacement hose from the Hydroboost unit to the back of the pump. About 4 hours of fun swapping out the pump, changing the pulley replacing the line, bleeding the system.

What happens when you bleed the brake pedal?

Bleed the brake on the opposite end next (the left front if you started with the right front). Test the brake pedal after all the brakes are bled. Once you are certain of a firm pedal, drive the vehicle at more than three miles per hour so the controller can automatically reset the system.

Why is my brake pedal soft on my 2004 Silverado?

I am having trouble trying to fix a low and soft brake pedal on my 2004 Silverado. I have already replaced the master cylinder, flushed and bled the brake lines at all four wheels. Still the pedal is low and soft. Does anyone know what it could be? There is no loss of brake fluid any where. The master cylinder reservoir is not losing fluid.

When does the brake pedal go to the floor?

Brake Pedal Goes to the Floor: I Replaced My Pads on My 2004 Chevy… I replaced my pads on my 2004 chevy silverado and bled the brakes. I know I did all this right.

How do you know if your brakes are working on a Chevy Silverado?

Go about 30 mph and hit the brake pedal firm and hard. You should feel the pedal pulsate , which indicates that the system is working. Do this 4 or 5 times, then go back and bleed the brakes in the proper sequence.

Why is there no pedal on my new master cylinder?

No Pedal with New Master Cylinder Installation – Quick Fix or Check? A “no brake pedal” condition can be encountered after a new master cylinder is installed, leading the technician to believe that the master cylinder is defective.

What happens when you take your foot off the pedal?

Your brakes should let go immediately as you take your foot off the pedal. If they don’t, this can cause brake overheating as well as premature wear to brake parts. Check these potential problems: Bad Wheel Cylinder: A bad wheel cylinder may not relax and release its pressure.

What happens when your brake pedal sinks to the floor?

If the pedal sinks to the floor, there is an issue in your braking system that should be addressed as soon as possible. The inability to stop quickly is very likely to cause a serious accident. Technically, there are three main causes that would make the brake pedal sink all the way to the floor.

What to do when your brake pedal goes to floor?

The first thing to check when your brake pedal goes to floor is to raise the hood and check the brake master cylinder’s reservoir. If the reservoir is empty or the brake fluid level is low, there is most likely a leak somewhere in the brake system.

What to know about no brake pedal condition?

A good indication of this condition is lack of fluid flow from the brake bleeders. Ensure master cylinder is bench bled prior to installation. Follow the vehicle’s manufacturer-specified bleeding procedure.

What causes a brake master to stop working?

Pumping the brakes can cause these seals to expand and may help the brake master start working again. When this failure occurs, the brake master cylinder must be replaced with a new unit. Bleed the Brake System: Air in brake system can cause the system not to pressurize or pump up.

What causes a brake caliper to go to the floor?

If the backside of the tire is wet with fluid either you have a brake caliper that is leaking and must be replaced or a wheel cylinder that has gone bad and needs replacing. Both of these problems allow a fluid leak through their brake fluid seals.

What to do when your brake pedal is near the floor?

At this time air can be pulled into the system in small quantities which causes the brake pedal to be near the floor. Bleed the brake system while checking for air in the form of bubbles being released from the bleeder screws and replace the brake components which air is observed from.

Why does my brake pedal stick when bled?

When the system is manually bled, the pedal is often depressed completely, moving the primary and secondary pistons to their extreme forward position (figure 2). The primary piston can stick even though there are springs attempting to push it back in position.

What to do if your brake pedal goes to the floor?

In case the brake pedal goes to the floor, there are several actions to be taken in order to fix the issue. The first action you can take is to check the level of the brake fluid. If the fluid is full, it means that there is no leak. If some fluid is missing or it is empty, it means that you have a leak somewhere.

Why does my brake pedal feel so soft?

The final reason why your brake pedal may be soft is because your master cylinder is failing. A master cylinder may fail due to age and wear. The master cylinder is the main valve that pumps brake fluid into your brake lines. When the cylinder is failing, your lines do not get the brake fluid needed.

Where does the low brake pedal come from?

In the next 5 minutes, you will have identified whether the issue causing your low pedal is in the front of your brake system or rear. Nearly every vehicle has a rubber hose at the center of the rear axle that attaches to a block on the rear end.

What causes the brake pedal to sink to the floor?

Brake shoes are only found on drum brake equipped vehicles. There will never be a drum brake on front of a modern vehicle. A shoe that is worn down too far will cause the pedal to sink closer to the floor than it normally would. This would be something to look at if there was no fluid leak detected.

What should I do if my Mercedes Benz won’t start?

Start the car and you should be able to get around 60 psi. When the engine is running and when you turn off the engine the pressure should stay steady. Always perform this test on a cold engine. Next, make sure that the fuel injector connections are secure and not loose. Check the fuel pump and the fuel pump relay.

Can a faulty brake light switch cause a car to not start?

In cars with a push-button start system, a faulty brake light switch can cause the vehicle not to start. Often, a brake light switch might be sticking and work intermittently. This can cause the Check Engine or ABS system warning light to come on on the dash.

What causes the accelerator pedal to stop working?

The primary reason why this part fails is due to exposure to high heat, as it’s typically located on the floorboard next to the firewall of the vehicle, in very close proximity to the engine.

What to do if your brake pedal won’t work?

Once the car shuts off there is no longer a vacuum source. It won’t take long for your brake pedal to go stiff after this point. That being said I would start at the starter, get the car running, and if the pedal is still stiff at that point, then take a look at the brakes. Jun 08 2008 29690

Why does my car not start when I press the brake?

* The brake pedal is extremely stiff (that is what she said) and i can’t depress it very far all at. * Brake lights turn on when pressing the pedal (so that i believe rules out the switch). * Tried jumping it for the hell of it, dind’t make any difference. * Nothing physically blocking the pedal.

How to diagnose hard brake pedal master power brakes?

A) With the engine not running, press and depress the brake pedal several times to remove any vacuum from inside the booster. B) On the last push of the brake pedal, hold moderate pressure on the brake pedal. Don’t push like you are panic stopping, but simply hold pressure like you are sitting at a red light.

How can I tell if my brakes are not working?

If your brakes are worn or not properly functioning, your car may take more time to stop or may not be able to stop altogether, both of which can lead to an accident. One of the signs that your brake system is not properly functioning is the brake pedal being soft or spongy, which means the pedal goes down to the floor when pushed.

What to do when your foot is on the brake pedal?

Don’t push like you are panic stopping, but simply hold pressure like you are sitting at a red light. C) With your foot still on the brake pedal, start the engine and pay attention to what happens to the brake pedal. One of two scenarios is going to happen:

Why is the brake pedal going to the floor?

If your brake pedal is going to the floor, it indicates that there is a serious problem in the braking system. When the pedal goes to the floor, it’s usually caused by a bad master cylinder, leaking brakes, bad brake shoes (if equipped with rear drums), and a few other reasons.

Why does my brake pedal go to the floor?

One of the more common causes for the brake pedal going to the floor is a loss of brake fluid.

What causes hard brake pedal?

Causes of Intermittent Hard Brake Pedal Not Enough Vacuum. Hard brakes are often the result of not having enough vacuum in the hose. Wrong Hoses or Hose Damage. Most of the time wrong hoses aren’t something you have to worry about in a car. Defective Brake Booster Check Valve. Bad Brake Booster. Pedal Ratio.

What’s wrong with my brakes?

Worn or Bad Brake Pads: If your brakes are very worn, or if they have become contaminated or are otherwise bad, you’ll need to replace your brake pads. Bad Brake Disc: Inspect your brake discs. If one or both are bad, they can cause your brakes to grab suddenly or unevenly. You’ll need to replace your brake discs.

Why is there no pressure on my rear brakes?

If there are no brake fluid pressure rear brakes, check for the pipes that deliver brake fluid to the rear brakes. Sometimes these pipes are exposed to corrosion that makes it have holes and leak the brake fluid. This makes the rear wheels not to bleed air, and make no pressure in the rear wheels.

What to do if your rear brakes are not working?

Any electrical faults in the rear ABS system are generally indicated with a light illuminated and if so, then the flash codes can be read out. But with no light illuminated then there most likely no electrical failures in the system.

Why is no brake fluid getting to the rear brakes?

No brake fluid is getting to the rear brakes dodge brake I have been trying to figure out why my rear brakes are not getting any brake fluid. This problem just occurred this week.

How to fix a brake pedal that sinks in your car?

How to fix a brake pedal that sinks to the floor when you stop by replacing the brake master cylinder. Brake master cylinder location, removal and replacement. DIY car repair with Scotty Kilmer, an auto mechanic for the last 43 years. 1. Flare Wrench Set: http://amzn.to/2kGaeGm 2. Large Screwdriver: http://amzn.to/2igwntV 3.

Navigation