What does f1 mean on GSXR 1000?

What does f1 mean on GSXR 1000?

SOURCE: on a 2004 suzuki gsxr. FI stands for Fuel Injection. The fuel system sensors have detected a problem. It could be anything > a dirty air filter FI stands for Fuel Injection. The fuel system sensors have detected a problem.

What does f1 mean on Hayabusa?

It an FI light. Fuel injection.

How many cylinders does a GSXR motorcycle have?

Because a GSXR should be able to run (badly) on 3 cylinders, and cleaning the fuel cap shouldn’t make a difference to just one cylinder.

Why is one cylinder not firing on GSX are 750?

A tear in the CV diaphragm at the top of a single carb is possible. This would create a very lean condition that would be more pronounced when your choke is engaged. When you go off choke the vacuum is reduced and the lean condition is less evident. While riding, downshift and go off throttle, if you get popping in your exhaust check the diaphragm.

What are the attributes of a GSXR 750?

The GSXR 750 has the following attributes. Carb and FI versions depending on year. If a coil were bad you would have an issue with two cylinders more than likely. Coils going bad on high energy lead connection to the coil is very rare. A sticking float bowl on a single carb. Check needle and seat and ensure the needle is dropping down

Why is one cylinder not firing on my motorcycle?

Take your finger and wipe it in the exhaust pipe exit. If it’s really black and oily then you may have a bad valve guide or rings. If it’s just black and sooty then your too rich. If the color is not black but a bit brown, that’s better and indicates a more normal mixture and lack of oil in the exhaust. Bad high energy lead.

Because a GSXR should be able to run (badly) on 3 cylinders, and cleaning the fuel cap shouldn’t make a difference to just one cylinder.

A tear in the CV diaphragm at the top of a single carb is possible. This would create a very lean condition that would be more pronounced when your choke is engaged. When you go off choke the vacuum is reduced and the lean condition is less evident. While riding, downshift and go off throttle, if you get popping in your exhaust check the diaphragm.

What to do if your GSXR won’t start?

First, John will show you where to locate the starter solenoid and fuse on the GSXR starting system and then test them. If it fails, you can replace the fuse with the extra fuse located on the machine or with a new fuse from partzilla.com. If that doesn’t work, the problem may be in the starter relay.

The GSXR 750 has the following attributes. Carb and FI versions depending on year. If a coil were bad you would have an issue with two cylinders more than likely. Coils going bad on high energy lead connection to the coil is very rare. A sticking float bowl on a single carb. Check needle and seat and ensure the needle is dropping down

What does F1 mean on GSXR 1000?

What does F1 mean on GSXR 1000?

SOURCE: on a 2004 suzuki gsxr. FI stands for Fuel Injection. The fuel system sensors have detected a problem. It could be anything > a dirty air filter FI stands for Fuel Injection. The fuel system sensors have detected a problem.

What is the F1 code on a Suzuki GSXR 1000?

Click to expand… This is weird, after riding my 2002 GSXR-1000 over 19,000 miles I get the F1 code C46. I follow the directions according to the link which the white connection was still plugged up to the Servo and splice the other two wires B/R & R/B. Code is gone which I tested this after for over 1 hour.

What does Fi mean on Suzuki GSXR 2006?

After riding over 10,000 miles on my 2006 750, FI started to show instead of temperature… (only) sometimes. Took it to dealer who said it needed to adjust exhaust valve (the wires) – as the error was shown because the valve did not fully close. 8,000 more miles since then and no problem. ..

What is the c00 code on a 2005 GSXR1000?

On 2005 GSXR1000 when I install the jumper I get the C00 code. How do I get rid of the F1 and light if nothing is wrong?Looked through everything listed and I did not see anything about it.

Where is the dealer mode switch on a Suzuki GSXR?

Location of dealer mode switch and how to get the codes. The dealer mode connector is under the tail cowling on the left side of the bike, near the regulator/rectifier. It will have only two wires going to it.

Click to expand… This is weird, after riding my 2002 GSXR-1000 over 19,000 miles I get the F1 code C46. I follow the directions according to the link which the white connection was still plugged up to the Servo and splice the other two wires B/R & R/B. Code is gone which I tested this after for over 1 hour.

How do you get Fi code flashing on Suzuki GSX-R?

With your key in the ignition and bike turned to “on” (but not running), take a paperclip and short the two connectors out (by touching the two contacts together). This is known as a “ghetto dealer mode switch”.

After riding over 10,000 miles on my 2006 750, FI started to show instead of temperature… (only) sometimes. Took it to dealer who said it needed to adjust exhaust valve (the wires) – as the error was shown because the valve did not fully close. 8,000 more miles since then and no problem. ..

What does dealer mode switch on Suzuki GSX-R do?

This is known as a “ghetto dealer mode switch”. It should display the error code on your display instead of just FI now. You might want to consider buying JeffW’s Dealer Mode switch…He’s an upstanding guy (ask anybody on gixxer.com) and sells great products.