Where is the starter on a Harley Davidson 883 Sportster?
Connect your red probe to the solenoid positive wire. This is a fat 12 or 14 gauge wire on the cylindrical portion of the starter. Connect the black probe to a known good ground. 12v should be present in this wire at all times. Figure 3. The starter location on a 883 Sportster.
How to reset check engine light on Harley Davidson Sportster?
These are general throttle idle cables. Start by turning the ignition switch into the “OFF” position. Next, turn the run/stop switch into the “RUN” position. Press and hold the odometer reset button. Put the ignition switch into the “IGNITION” position and take your hand off the odometer reset button.
What does it take to start a Harley Davidson Sportster?
This article applies to the Harley Davidson Sportster. What does it take to start a Sportster? When you turn the ignition switch to the on position, current is sent to the start button. Pressing the button sends power to the starter solenoid, which sends a large amount of current from the battery to the starter to turn the motor.
What should the Run switch read on a Harley Davidson Sportster?
Remove the kill switch from the right handlebar grip. Measure the resistance/continuity of the switch with the switch unpressed using the same method described for testing the run switch. The reading should be 0.1 ohms or less. Press the switch and measure again. The reading should now be “OL” or infinite, meaning no connection is present.
Connect your red probe to the solenoid positive wire. This is a fat 12 or 14 gauge wire on the cylindrical portion of the starter. Connect the black probe to a known good ground. 12v should be present in this wire at all times. Figure 3. The starter location on a 883 Sportster.
How to order a 2020 Harley Davidson Sportster?
2020 Harley Davidson Sportster Iron XL883N Parts & Accessories – RevZilla Skip to Main Content RevZillaSpeak to an expert: 877-792-9455 Customer Service Order Status Track Your Ride Log In/Sign Up
How to order Harley Davidson Sportster iron xl883n parts?
2020 Harley Davidson Sportster Iron XL883N Parts & Accessories – RevZilla Skip to Main Content RevZillaSpeak to an expert: 877-792-9455 Customer Service Order Status Track Your Ride Log In/Sign Up My Garage Access Saved Bikes Create an Accountor Log Into store your bikes and shop exact-fit parts in a single click.
Is there a gas light on a Harley Davidson Sportster?
Gas light. Harley Sportster only got anti-lock brakes as an option in 2014, and it is such a simple system you may not even know your bike is equipped with it. If when you start the bike the ABS light light up, that means you have anti-lock brakes.
How can you tell if a Harley Davidson starter is working?
In addition to the starter current draw test, you can measure the voltage at the wire connected to the starter solenoid from the ignition switch. With the ignition in the on/run position and the button pressed, 12 volts should be present at this wire. This test will also tell you if the ignition switch is working.
How do you test the Kill Switch on a Harley Davidson?
To test the kill switch: Remove the kill switch from the right handlebar grip. Measure the resistance/continuity of the switch with the switch unpressed using the same method described for testing the run switch. The reading should be 0.1 ohms or less. Press the switch and measure again.
How to test if your starter switch is working?
6) Breaker panel wires to the starter relay were tested. accessories, am I okay in assuming the the ignition switch itself is working? A common wire black/red are used in the circuit panel for ignition, instruments, and lights. The black/red wire is connected to the starter relay via SPL8 (another bundle).
Remove the kill switch from the right handlebar grip. Measure the resistance/continuity of the switch with the switch unpressed using the same method described for testing the run switch. The reading should be 0.1 ohms or less. Press the switch and measure again. The reading should now be “OL” or infinite, meaning no connection is present.
In addition to the starter current draw test, you can measure the voltage at the wire connected to the starter solenoid from the ignition switch. With the ignition in the on/run position and the button pressed, 12 volts should be present at this wire. This test will also tell you if the ignition switch is working.
Why is my Harley Davidson Sportster not starting?
Place your Sportster in second or third gear for the best results. A battery that can’t start your engine may no longer be recharging properly because of its age and current state of charge. The ground cables that connect the battery to your Sportster frame must also be undamaged and free of corrosion.
What should the current be on a Harley Davidson starter?
In addition to the starter current draw test, you can measure the voltage at the wire connected to the starter solenoid from the ignition switch. With the ignition in the on/run position and the button pressed, 12 volts should be present at this wire.
Place your Sportster in second or third gear for the best results. A battery that can’t start your engine may no longer be recharging properly because of its age and current state of charge. The ground cables that connect the battery to your Sportster frame must also be undamaged and free of corrosion.
In addition to the starter current draw test, you can measure the voltage at the wire connected to the starter solenoid from the ignition switch. With the ignition in the on/run position and the button pressed, 12 volts should be present at this wire.
Is the ignition on a Harley Davidson a good question?
Is this a good question? buy after market round key ignition with 3 wires,Disconnect battery, splice into wiring loom, use electrical connectors to connect new wires into loom wires,If not get a electrical Mechanic to do it for you,Thats what i did cost £25to buy £20 to fit.job done, Was this answer helpful?
Is there a problem with the ignition on a Harley Davidson?
Thanks george,but its none of the above you wrote,My Harley is garage,I finally found out it was a contact inside ignition that had broke away due to flat keys riggling about because of vibration of engine,all 2015 wide glides also have same problem and have been recalled,over 3000 bikes.
What makes a bad Sportster a good Sportster?
That combined with the belt drive giving no driveline lash makes for extremely smooth acceleration. The other thing that the EFI gave was a non-traumatic first start up in the spring. No hooking up the battery to a car, no lighter fluid, no carb cleaning, no playing with the throttle.
Is the EFI on a Sportster good or bad?
Plus the EFI on the Sportsters is almost perfect. That combined with the belt drive giving no driveline lash makes for extremely smooth acceleration. The other thing that the EFI gave was a non-traumatic first start up in the spring. No hooking up the battery to a car, no lighter fluid, no carb cleaning, no playing with the throttle.
Where is the start relay on a Harley Davidson?
It is the GRAY one. On the inside cover there is a label that will identify the START Relay. 4) Look at the bottom of the removed gray relay closely. You will see pin notation as follows. 87,,87A,,30,,85,,86. 5) Leave the relay REMOVED from the bike.
How to disable tilt alarm on Sportster Fixya?
Then remove the magnet and do the same again, If it is normally open or if it normally closed then you can decide how it works. If it is activated then the ECM will not allow a start until the bike has been returned to the upright position and the ignition has been cycled off and on.
Why is my Harley Davidson Sportster not igniting?
One of the most common sources of electrical problems is the battery. Test the battery’s state of charge and current capacity by reading Step 2 of the article Electrical Diagnostic Guide. If no spark is present at the end of the spark plug wire, the air/fuel mixture cannot ignite.
Where is the ignition sensor on a Harley Davidson Sportster?
The crankshaft position sensor location. The I.C.M. (ignition control module) was used on Sportsters before the year 2007. After 2007, the module became integrated into the E.C.M. (electronic control module). These modules contain internal circuitry found on most computer motherboards.
How does the ignition coil work on a Harley Davidson Sportster?
The ignition coil on later model Sportsters. The crankshaft position sensor is used to determine the crankshaft’s speed and position. The E.C.M. or ignition module uses this information to correctly time the spark at the spark plug with the piston.
What causes a starter to blow a circuit breaker?
Something is shorting to blow the breaker. Since it is only happening when you hit the start button you would have to guess that the starter circuit is going to ground. Follow the wires and look for bare spots. Could be the starter motor/solenoid. This link is for cars but the principal for checking applies Bench Testing a Starter Motor