How do you turn off the seat belt chime?
Repeat the above two steps, buckling and unbuckling the seat belt 2 more times ending up with the seat belt buckled. Be sure to wait for the light to turn on or off each time. You must complete this within 60 seconds. If you hear a chime while doing this, turn off the car and start over.
How to disable the seat belt alarm on your car?
How to Disable a Seat Belt Alarm 1 Beware of the airbag risk. 2 Check the user manual or ask your reseller to disable it per software. 3 Disable your alarm. See More….
How to turn off the seat belt warning / chime on a Dodge Grand Caravan?
After much reading on the web and a lot of trial and error, I have finally figured out how to turn off the annoying chime the Dodge minivan makes when you don’t buckle your seat belt. This works with my 2007 Dodge Grand Caravan, but other years and model Dodge cars will probably work as well.
How do you replace a seat belt cover?
You’ll need a set of security Torx bits and two very small zip ties. Remove the cover from the seat belt buckle, two Torx bolts each. There is a switch that will close when the seat belt is fastened. Use the zip tie to close that switch full time. Replace the cover. Do the other side. You’ll never hear that chime again.
How to Disable a Seat Belt Alarm 1 Beware of the airbag risk. 2 Check the user manual or ask your reseller to disable it per software. 3 Disable your alarm. See More….
How can I tell if my seat belt is connected to the airbags?
Yes. To verify if they’re connected, try looking under your seat. The connector for the seat belt lock will often be a bright color, and if you see it, that means it’s connected to the airbags. However, not all car models will have this feature. If you’re not sure, take your car to the dealership or ask your manufacturer. Thanks!
Why does my car Ding when I dont have my seat belt on?
Because there are sometimes during short drives where you just really don’t want to be told what to do. This method works for most cars or trucks that have the constant seat belt ‘ding’ that goes off if you or your passenger don’t have your seat-belt on.
What happens if you cut the seat belt sensor?
Tampering with your seat belt sensor in any way can affect airbag performance. This can put you and/or your passengers at serious risk. Be sure that your airbags will not be affected before altering your seat belt alarm sensor. Do not attempt to cut the buckle harness.
How to disable seatbelt alarm / chime in Subaru?
Turn the vehicle to the on position by either turning the key to the on (without starting it) or hitting the push to start button twice without touching the brake pedal. Buckle and unbuckle the seatbelt twenty (20) times in thirty (30) seconds. The seat belt chime is now disabled.
How to turn off the seat belt warning?
Unbuckle the seat belt, and wait for the seat belt warning light to go on. Buckle the seat belt and wait for the seat belt warning light to go off. Repeat the above two steps, buckling and unbuckling the seat belt 2 more times ending up with the seat belt buckled. Be sure to wait for the light to turn on or off each time.
How to activate / deactivate chime and airbag warning indicator?
Deactivating/Activating: 1. Turn the ignition switch to position II. (Do not start the engine). 2. The airbag warning indicator will extinguish within 10 seconds. 3. NOTE: Step 3 must be completed within 60 seconds or the procedure must be repeated. Buckle then unbuckle the safety belt nine times, ending with the safety belt unbuckled. 4.
Repeat the above two steps, buckling and unbuckling the seat belt 2 more times ending up with the seat belt buckled. Be sure to wait for the light to turn on or off each time. You must complete this within 60 seconds. If you hear a chime while doing this, turn off the car and start over.
Turn the vehicle to the on position by either turning the key to the on (without starting it) or hitting the push to start button twice without touching the brake pedal. Buckle and unbuckle the seatbelt twenty (20) times in thirty (30) seconds. The seat belt chime is now disabled.
Unbuckle the seat belt, and wait for the seat belt warning light to go on. Buckle the seat belt and wait for the seat belt warning light to go off. Repeat the above two steps, buckling and unbuckling the seat belt 2 more times ending up with the seat belt buckled. Be sure to wait for the light to turn on or off each time.
Deactivating/Activating: 1. Turn the ignition switch to position II. (Do not start the engine). 2. The airbag warning indicator will extinguish within 10 seconds. 3. NOTE: Step 3 must be completed within 60 seconds or the procedure must be repeated. Buckle then unbuckle the safety belt nine times, ending with the safety belt unbuckled. 4.