What does OBDII code p0341 mean on Honda CRV?
P0341 is a somewhat common OBDII diagnostic code in the Honda CR-V. It means that there is a Range/Performance problem. In layman terms this means that there is a problem with the signal coming from the Camshaft Position Sensor (CPS). OBDII P0341 means that there is a problem with the Camshaft Position Sensor (CPS) circuit.
What causes DTC p0341 on a Honda Element?
2003–2010 Element A damaged or stretched cam chain, resulting from infrequent oil changes, can cause the MIL to come on with DTC P0341 (CMP sensor A and CKP sensor incorrect phase detected). Old oil causes the cam chain to wear quickly. As a result, it stretches beyond the point where the cam chain auto-tensioner can keep up.
What does the engine light on p0341 mean?
The camshaft position sensor signal sent to the Engine Control Module(ECM) during the first few seconds of engine cranking is out of range. P0341 HONDA Possible Symptoms Engine Light ON (or Service Engine Soon Warning Light) Possible lack/loss of power Engine may stall while driving P0341 Honda Description
What is the correct phase for the DTC p0341?
DTC P0341: CMP Sensor A and CKP Sensor Incorrect Phase Detected 1. Confirm the failure (part 1). 2. Confirm the failure (part 2). Pass 3. Check the camshaft timing. 4. Check for a damaged or stretched cam chain. 5. Check for a clogged VTC oil control solenoid valve. 6. Check for a stuck open VTC oil control solenoid valve. 7.
What does diagnostic code p0341 mean?
This diagnostic trouble code (DTC) is a generic powertrain code, which means that it applies to OBD-II equipped vehicles. Although generic, the specific repair steps may vary depending on make/model. This P0341 code basically means that the powertrain control module (PCM) detected a problem with the camshaft signal.
What is OBD code p0341?
P0341 is an OBD-II generic code that says the engine control module (ECM) detected the engine camshaft position sensor circuit is not within specifications. The sensor pulses do not correlate to the pulses of the crankshaft sensor.
What is Crv used for?
Introduced by Honda in 1995 as the name for its car-based utility vehicle, the acronym “CRV” (as in Honda CR-V) represents a mix between a car or minivan and a sport utility vehicle, or SUV. There are at least two official definitions of its meaning. Some say its stands for “compact recreation vehicle,” while others insist it’s…
When does PCM set trouble code p0341?
As certain points of the reluctor wheel pass by the camshaft sensor, the sensor regulates 5 volt reference voltage in a wave pattern. Anytime the camshaft sensor signal does not correspond to the signals received from the crankshaft sensor, the PCM sets a trouble code P0341.
What is the misfire code on Honda CRV p0301?
P0301 is a cylinder specific misfire code, which means that cylinder 1 is misfiring and causing the code.
What does the CPS code on a Honda CRV mean?
P0341 is a somewhat common OBDII diagnostic code in the Honda CR-V. It means that there is a Range/Performance problem. In layman terms this means that there is a problem with the signal coming from the Camshaft Position Sensor (CPS).
P0341 is a somewhat common OBDII diagnostic code in the Honda CR-V. It means that there is a Range/Performance problem. In layman terms this means that there is a problem with the signal coming from the Camshaft Position Sensor (CPS). OBDII P0341 means that there is a problem with the Camshaft Position Sensor (CPS) circuit.
2003–2010 Element A damaged or stretched cam chain, resulting from infrequent oil changes, can cause the MIL to come on with DTC P0341 (CMP sensor A and CKP sensor incorrect phase detected). Old oil causes the cam chain to wear quickly. As a result, it stretches beyond the point where the cam chain auto-tensioner can keep up.
P0301 is a cylinder specific misfire code, which means that cylinder 1 is misfiring and causing the code.
P0341 is a somewhat common OBDII diagnostic code in the Honda CR-V. It means that there is a Range/Performance problem. In layman terms this means that there is a problem with the signal coming from the Camshaft Position Sensor (CPS).
What is the problem with the p0341 sensor?
P0341 – Camshaft position (CMP) sensor A, bank 1 range/performance problem Trouble Code Fault Location Probable Cause P0341 Camshaft position (CMP) sensor A, bank 1 Insecure sensor/rotor, air gap, wiring,
How to diagnose p0341 on a 2009 VW?
P0341 Code: Camshaft Position Sensor ”A” Circuit Range/Performance (Bank 1 or Single Sensor) – In The Garage with CarParts.com How to diagnose P0341 on a 2009 VW CC
What is the p0341 code for Camshaft Position Sensor?
P0341 code is triggered when the powertrain control module (PCM) detects a problem with the signal being sent by the camshaft position sensor. To learn more about how the ECM/PCM uses signals from the CMP, you can read our in-depth explanation here.
What does a p0341 camshaft position sensor code mean?
Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. What does this mean? Sometimes and in some models, low battery voltage or a weak starter can trigger a Camshaft Position Sensor code. The cost to diagnose the P0341 code is 1.0 hour of labor.
How to fix and clear OBD-II trouble code p0341?
Often replacing the camshaft sensor fixes trouble code P0341, however it is important to check the following first: Inspect the wiring at the camshaft sensor for melting or marks of corrosion Inspect the camshaft reluctor wheel for missing or damaged teeth.
What does trouble code p0341 camshaft position sensor mean?
In those cases it basically means the engine is misfiring badly due to faulty spark plugs, spark plug wires, and often coils. Often relacing the sensor fixes this code, but not necessarily. Therefore it’s important to check the following:
Often replacing the camshaft sensor fixes trouble code P0341, however it is important to check the following first: Inspect the wiring at the camshaft sensor for melting or marks of corrosion Inspect the camshaft reluctor wheel for missing or damaged teeth.
Why does my Honda Element come on with p0341?
2002–2010 CR-V 2003–2010 Element A damaged or stretched cam chain, resulting from infrequent oil changes, can cause the MIL to come on with DTC P0341 (CMP sensor A and CKP sensor incorrect phase detected). Old oil causes the cam chain to wear quickly. As a result, it stretches beyond the point where the cam chain auto-tensioner can keep up.
What happens when you get a trouble code p0341?
A P0341 trouble code will generally trigger the check engine light on. Depending on your vehicle’s make, the check engine light may be referred to as the CEL, the Malfunction Indicator Lamp (MIL) or Service Engine Soon (SES) light.
Why do I have a DTC p0341 engine light?
As a result, it stretches beyond the point where the cam chain auto-tensioner can keep up. That extra chain slack causes the valve timing control (VTC) actuator and the exhaust camshaft sprocket to lag behind, and you wind up with DTC P0341.
What causes an OBDII code on a Honda?
P0341 HONDA Possible Causes 1 Faulty Camshaft Position Sensor 2 Camshaft Position Sensor harness is open or shorted 3 Camshaft Position Sensor circuit poor electrical connection 4 Faulty starter motor 5 Starting system circuit 6 Dead (Weak) battery
Why does my Mil come on with DTC p0341?
A damaged or stretched cam chain, resulting from infrequent oil changes, can cause the MIL to come on with DTC P0341 (CMP sensor A and CKP sensor incorrect phase detected). Old oil causes the cam chain to wear quickly.