Why do my brake lights and blinkers not work?

Here is what is going on: I have a 1998 Chevy Suburban 1500 4X4 5.7 with a blinker-tail light issue. Currently, I have brakes and hazard lights. … read more Vocational, Technical or Tra… Both tail lights and brake lights dont work right. the right turn signal works.

What causes brake lights to not work but tail lights do?

5 Causes of Brake Lights Don’t Work But Tail Lights Do 1 Bad Light Bulbs 2 Bad Brake Light Switch 3 Broken fuse or fuse box 4 Bad sockets and connectors 5 Broken wire More …

Why do my brake lights not work on my GMC Sierra?

I have a 1994 GMC Sierra C1500 2WD with 4.3l w/automatic. It was a fleet vehicle. Plain Jane accept for High Output Heater, Limited Slip Diff and Engine Block Heater. Brake lights were working intermittently. Would come on when pedal as first depressed then go out after pedal traveled down a bit. I put in a new switch and all was well for 3 months.

When do the brake lights turn on in a car?

The brake lights turn on when you apply pressure on the brakes. In most automobiles, the taillights are red while the brake lights are a brighter, more luminous red. The rear lights are controlled by the same switch as the headlights. The power flows through a relay to the rear lights when the switch is turned on.

Why is my rear brake light not working?

The rear brake light and turn signal is not working on the driver side. I have replaced the bulbs and the connectors but to no avail. I checked the fuses and they are fine as well. When I take my electronic key and unlock the truck the driver rear lights will not light up but when I lock the doors it does light up in the back.

Why is my brake and turn signal not working?

Before you do that, you will need to connect a scanner that can communicate with the BCM. Believe it or not, you could have a BCM code that is stopping your brake and turn signal lights from working. Most people don’t have access to a scanner that can access the BCM, so you will most likely need to book an appointment with us to do this.

Where is the brake light switch on my car?

Fuse Box and Light Switch. You have to find the fuse box or the power distribution center (PDC). You will get the fuse panel under the dashboard and the PDC under the hood. The brake light switch is also to be found under the dashboard and check if its plunger touches the brake pedal arm.

Why does the tail light stay on when the car is turned off?

There are many causes for tail light constantly staying on while the car is turned off: A broken brake light switch, damaged trailer light plug, faulty brake light switch stopper, broken wiring harness,… There are various reasons, however, you can check whether it is the brake lights or the tail lights to see which are the parts having problems.

What to do if there are no brake lights?

Cut repair costs, not quality. Here is some info for you. Fuse No.1 is for your brake lights and your hazard lights. If no lights after fuse, if found blown, is replaced check your light globes. If nothing works check that the fuse hasn’t blown again. Fuse 16 is for the turn lights.

Are there brake lights on my Chevy Silverado?

My brake lights and blinkers do not work on rear end of my 1998 Chevy silverado. Blinkers work on front end. Tail lights Chevrolet Silverado 1500: My brake lights and blinkers do not… No lights in the back. Brake, tail, blinkers. No lights at Professional at Justanswer… Vocational, Technical or Tra…

What is fuse No.1 for brake lights?

Here is some info for you. Fuse No.1 is for your brake lights and your hazard lights. If no lights after fuse, if found blown, is replaced check your light globes. If nothing works check that the fuse hasn’t blown again. Fuse 16 is for the turn lights.

What kind of car has no brake lights?

I have an 1994 Chevy Silverado 1500 I have problems with, when you turn on the headlights the tail lights and brake lights don’t work. With the … read more

Is it dangerous to drive without brake lights?

Driving during the night without brake lights or tail lights can thus be extremely dangerous. The problem is that you cannot often tell if your taillights and brake lights are faulty. Therefore, it is necessary for both your taillights and brake lights to work.

What to do when your brake lights are not working?

In the situation when brake lights are not working properly, you need to make sure that the power is going through and check the fuse. If the brakes lights are turned on at the same time as turn signal lights, you need to bring it to the mechanics for a check.

Where are the brake lights and tail lights?

In most European cars, the same bulb does the job of the tail and brake lighting. However, it has double filaments, allowing one set still working while the other set is burnt. You have to find the fuse box or the power distribution center (PDC). You will get the fuse panel under the dashboard and the PDC under the hood.

Is it illegal to drive without a brake light?

First of all, you will get pulled over and be fined by a police officer since it is definitely illegal to drive without a working brake light. Second of all, other drivers cannot see you very well in the dark. Without brake lights, it is impossible for them to know whether you are stopping or not, so accidents on the road are very likely.

Where do the brake lights go in a car?

The way those taillights work theres a white wire under dash on the column that white wire is for brake light. So the way the brake lights work they go through a relay and through blinker switch.

Why are the brake lights not working but the tail lights are?

Blown out light bulbs are the most common reason for why the brake lights not working but the tail lights are. Remove the screws from the bulb lens (which you can access through the trunk or see your vehicle repair manual to get the exact location). Push the bulbs and turn them counterclockwise to remove from the socket.

Can a bad signal switch cause a blinker not to work?

A faulty signal switch can’t send a signal to the blinkers to work. Sometimes the problem may lie in the wiring, or in the switch itself. If the problem lies with the switch then it’s likely getting stuck in position due to the clock-spring. Regardless, the problem isn’t the blinker itself, but the device that communicates with it.

What to do if your blinkers don’t work?

If the bulb in your signal dies, then it’s a pretty straightforward fix — simply replace it with a new one. Turn signal lights usually last a few years, but they can die quicker if you use them often. The turn signal switch is the device near your wheel which controls your signal. A faulty signal switch can’t send a signal to the blinkers to work.

Navigation