Why does my Yukon have a reduced engine power warning?

Why does my Yukon have a reduced engine power warning?

Here are some of the most typical problems that can make your Yukon’s reduced engine power warning come on: This is one of the most common reasons the reduced engine power light comes on.

When did my 2006 Yukon lose all power?

I purchased my 2006 Yukon last September 2005. I now have 24,000 miles on it. Over the last month I have had it into the dealer three times for the same problem. The problem is that while driving the vehicle it will suddenly lose almost all power.

Why does my GMC Yukon not go over 20 mph?

And the vehicle will not go over 20 mph on a level surface and bearly 3 mph up a moderately steep hill. Each time I have had it into the dealer for repair they have beeen stumped by what the cause of the problem is.

What should the fuel pressure be on a GMC Yukon?

Bonddog, I would suggest that a fuel pressure test be performed using a know good fuel pressure gauge should have 60psi minimum (critical) with the key being cycled on, pump is purchased as a complete module assembly very expensive and fuel filter should be performed when replacing the pump.

Here are some of the most typical problems that can make your Yukon’s reduced engine power warning come on: This is one of the most common reasons the reduced engine power light comes on.

How much does it cost to repair a GMC c0298?

The cost of diagnosing the C0298 GMC code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.

How to get GMC Yukon ABS code c0265?

Separate the EBCM from the BPMV by lifting upwards. Clean the sealing area with a rag and install the new EBCM. Install and tighten the 4 Torx bolts and then re-attach the whole unit back to the frame. It should be good to go, but may require programming. Be sure to clear any codes before driving.

Why is my abs code c0298 not working?

Code C0298 is a problem in the EBCM requested torque signal circuit to the PCM (Powertrain Computer). This can also be a ground problem. With the fact that both these codes have a ground circuit in common, that would be the first thing to have checked.

The cost of diagnosing the C0298 GMC code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.

Code C0298 is a problem in the EBCM requested torque signal circuit to the PCM (Powertrain Computer). This can also be a ground problem. With the fact that both these codes have a ground circuit in common, that would be the first thing to have checked.

Separate the EBCM from the BPMV by lifting upwards. Clean the sealing area with a rag and install the new EBCM. Install and tighten the 4 Torx bolts and then re-attach the whole unit back to the frame. It should be good to go, but may require programming. Be sure to clear any codes before driving.

What does the sensor code p0641 stand for?

The sensor in question is typically associated with the automatic transmission, transfer case, or one of the differentials. This code will almost always be accompanied by a more specific sensor code. The P0641 adds that the circuit is open.

I purchased my 2006 Yukon last September 2005. I now have 24,000 miles on it. Over the last month I have had it into the dealer three times for the same problem. The problem is that while driving the vehicle it will suddenly lose almost all power.

What is the throttle position sensor on a GMC Yukon?

The throttle position sensor is one of the most vital sensors in your Yukon. If it’s not responding, the ECU has no way of telling how much gas gas you’ve given it. The TPS data also helps determine when the transmission will shift.

And the vehicle will not go over 20 mph on a level surface and bearly 3 mph up a moderately steep hill. Each time I have had it into the dealer for repair they have beeen stumped by what the cause of the problem is.

Is the GMC Yukon XL a registered trademark?

2002 GMC Yukon/Yukon XL Owner’s Manual Litho in U.S.A. Copyright General Motors Corporation 6/18/01 Part Number X2216 A First Edition All Rights Reserved ii GENERAL MOTORS, GM, the GM Emblem, GMC, the GMC Truck Emblem and the name YUKON are registered trademarks of General Motors Corporation.

Where was the 2002 GMC Yukon XL purchased?

No accident or damage reported to CARFAX. 1st owner purchased on 03/05/02 and owned in OH until 02/17/04 • 2nd owner purchased on 10/02/04 and owned in OH until 07/22/16 • 3rd owner purchased on 03/27/17 and owned in KY until .

How many miles does a GMC Yukon XL drive?

1st owner purchased on 03/05/02 and owned in OH until 02/17/04 • 2nd owner purchased on 10/02/04 and owned in OH until 07/22/16 • 3rd owner purchased on 03/27/17 and owned in KY until 04/13/21. 1st owner drove an estimated 27,829 miles/year • 2nd owner drove an estimated 11,812 miles/year • 3rd owner drove an estimated 13,938 miles/year.

When was the GMC Yukon XL last serviced?

1st owner drove an estimated 8,598 miles/year • 2nd owner drove an estimated 0 miles/year • 3rd owner drove an estimated 8,406 miles/year. Last serviced at 49,843 miles in Galveston, TX on 09/06/07 • Vehicle serviced.

What are the codes for GMC check engine lights?

P1245Intake Plenum Switchover Valve P1250Early Fuel Evaporation Heater Circuit P1257Supercharger System Overboost P1258Engine Coolant Overtemperature – Protection Mode Active P1260Last Test Failed SCC Or Theft Detected, Vehicle Immobilized

Where is the trouble code on a GMC?

When retrieving GMC trouble codes with an OBD II scan tool, proceed as follows: 1. Connect scan tool to the 16-pin data link connector (DLC) located underneath the steering column. The connector may have a removable cover. 2. Turn the ignition on.

Why does my GMC Yukon lose all power?

The problem is that while driving the vehicle it will suddenly lose almost all power. The Information Center will display the messages: “Stability Control Disabled”, “Engine Power Reduced”.

When retrieving GMC trouble codes with an OBD II scan tool, proceed as follows: 1. Connect scan tool to the 16-pin data link connector (DLC) located underneath the steering column. The connector may have a removable cover. 2. Turn the ignition on.

P1245Intake Plenum Switchover Valve P1250Early Fuel Evaporation Heater Circuit P1257Supercharger System Overboost P1258Engine Coolant Overtemperature – Protection Mode Active P1260Last Test Failed SCC Or Theft Detected, Vehicle Immobilized