How much torque does a B series head nut have?

“ARP HEAD BOLTS”ALL B-SERIES <Clean block thread holes till dry> lube top nut threads only with 10w30 or ARP Molly lube then use 5/16 allen key to torque bolts to 10ft lbs into the block> Torque in steps: 30ft-lbs (360in-lbs),60ft-lbs>> (720in-lbs) Then to 80ft-lbs (960in-lbs)

What are the torque specs for a B Series car?

B18B,B16,B17,B18C Following the manufacturers recommended torque sequence, tighten the nuts in three equal steps to 30ft lbs,60ft lbs and then 80ft lbs with ARP ULTRA-TORQUE FASTENER ASSEMBLY LUBRICANT. Shown above is one cam cover, sequence is the same for intake and exhaust cam cover.

What are the torque specs for a VTEC?

Torque specs: Torque specs: CYLINDER HEAD BOLT TORQUE SPECS (tightening) / (loosening) 8, 4, 2, 6, 10 7, 3, 1, 5, 9. Torque in steps: 22ft-lbs (264in-lbs), Then to 63ft-lbs (756in-lbs) (final spec) 94+ Teg

Which is the correct torque for stud bolts?

The Final Torque Value accounts for 10% bolt relaxation. This Table is not acceptable for PTFE coated Stud Bolts and nuts, for these refer to Table 5. BOLTING TORQUE TABLE 3 – USE ONLY WITH A193 B8, CL1 BOLTS AT 540°C – 650°C ON UNINSULATED FLANGES

“ARP HEAD BOLTS”ALL B-SERIES lube top nut threads only with 10w30 or ARP Molly lube then use 5/16 allen key to torque bolts to 10ft lbs into the block> Torque in steps: 30ft-lbs (360in-lbs),60ft-lbs>> (720in-lbs) Then to 80ft-lbs (960in-lbs)

What is the torque of an A193 B8 bolt?

Torque values for bolts greater than 1.1/2 in. diameter are based on 30 ksi yield strength. BOLTING TORQUE TABLE 3 – USE ONLY WITH A193 B8, CL1 BOLTS AT 540°C – 650°C ON UNINSULATED FLANGES

What are the torque specifications of a Honda 1.8L 112ci S4?

31.18 Crankshaft To Engine Block 75.93 Cylinder Head To Engine Block 84.06 Drain Plug To Oil Pan Exhaust Manifold To Cylinder Head Exhaust Manifold To Exhaust Pipe Flexplate/Driveplate To Crankshaft Flywheel To Crankshaft Fuel Rail To Intake Manifold Heat Shield To Intake Manifold

Where is the exhaust manifold on a Honda 1l-112ci?

Camshaft To Cylinder Head 9.49 Connecting Rod To Crankshaft 31.18 Crankshaft To Engine Block 75.93 Cylinder Head To Engine Block 84.06 Drain Plug To Oil Pan Exhaust Manifold To Cylinder Head Exhaust Manifold To Exhaust Pipe

What are the torque specs on a Honda Civic?

This article applies to the Honda Civic (incl. Del Sol) (1992-2000). Tightening your bolts too much or not enough can cause a part to fail, and depending on the part, can put your life and the lives of the any passengers in danger. Most parts come with bolt-tightening torque specs, and your owner’s manual should have this information too.

What should the torquing specs be on a HO engine?

Note: Be sure to lightly oil the bolt threads for proper torquing specs for bolts not in the water jackets, otherwise use liquid thread sealer for the bolts that are in the water jackets (bottom ones).

What are torque specs for J series engine?

NOTE: Dip main bearing bolts and crankshaft damper bolt in clean engine oil prior to tightening.

When to use new bolts on Honda Civic?

Manufacturers design bolts and screws to “stretch” when they’re install. That way, the bolt and screw threads firmly attach to the matching threaded hole or nut. This lowers or outright eliminates the risk that the bolt or screw will work itself loose. For the same reason it’s always a good idea to use new bolts when working on the engine.

How much torque does a troque engine have?

Main bearing cap bolts. Torque: 39 N·m (29lb ft) NOTE: Do not allow the crankshaft to rotate. Crank case Main Bearing side bolt Torque: 39 N·m (29lb ft) Connecting Rod Cap bolts Torque: 54 NÂ·m (40 lb ft). Install main bearing caps, oil gallery and crank case bolts in the order shown, and tighten each bolt to the specified torque.

How much torque does a crank case have?

Crank case Main Bearing side bolt Torque: 39 N·m (29lb ft) Connecting Rod Cap bolts Torque: 54 NÂ·m (40 lb ft). Install main bearing caps, oil gallery and crank case bolts in the order shown, and tighten each bolt to the specified torque. NOTE: Do not apply engine oil to the crank case side bolts.

What are the torque specifications of a Ford 5.4L V8?

Type: Bolt Engine Mount To Engine Block 45 540 61.01 Modular OHC – Engine Mount to Engine Block Bolts Type: Bolt Head: Hexagon 45 540 61.01 Modular OHC – Engine Mount Thru Bolts Type: Bolt Exhaust Manifold To Cylinder Head 18 216 24.4 Modular OHC – Exhaust Manifold NUTS Type: Exhaust Manifold To Cylinder Head 9 108 12.2

What are the torque specs for stock bolts?

These specs are for stock-type bolts with light engine oil applied to the threads and the underside of the bolt head. Moly and other lubes offer reduced friction and increased bolt tension, which will affect the torque figure. If you use after-market performance bolts like ARP’s, you should follow the recommended torque specifications.

What are the torque specs for a Chevy big block?

Bolt Torque Spec Chart for Chevy Big Block Chevy Fastener Type Torque Specs Main cap bolt, 396-427 2-bolt 95 ft.-lbs. Main cap bolt, 396-454 4-bolt (inner/outer) 110 ft.-lbs. 3/8 in. connecting rod bolt 50 ft.-lbs. 7/16 in. connecting rod bolt 67-73 ft.-lbs. Cylinder head bolts, long 75 ft.-lbs. Cylinder head bolts, short 65-68 ft.-lbs.

What are the torque specs for a Ford engine?

Ford Engine Bolt Torque Chart Fastener Type Torque Spec Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs.

What should the torque be on an ARP bolt?

If you use after-market performance bolts like ARP’s, you should follow the recommended torque specifications. 40-45 ft-lbs. (45-50 ft-lbs. For Boss 351C) 105 ft-lbs. (125 ft-lbs. For Boss 351C) 40-45 ft-lbs. (53-58 ft-lbs. For 406 and 427) 80-90 ft-lbs. (100-110 ft-lbs. For 1963-67 427)

Navigation