What does fault code SPN 102 FMI 18 mean?
DescriptionThis Fault Code Sets When the Intake Manifold Pressure is Lower Than Expected While The Engine is Under a Load Typical Enabling ConditionsEngine Coolant Temperature greater than 65°C (149°F)
When does a Volvo engine fault code become inactive?
Some fault codes become inactive when the engine is stopped. Start the engine to check whether the fault code is still inactive with the engine running. After an action with the connector. Put the connector back. Check if the fault code becomes inactive.
What does the PID stand for on a Volvo?
The PID consists of a number that designates a parameter (value) to which the fault code relates (oil pressure, for example). The same as the PID, but this is a Volvo-specific parameter.
What does FMI stand for in a fault code?
FMI indicates the type of fault (please refer to the FMI table below). Data valid but above normal operational range. Data valid but below operational range. Voltage above normal or shorted high. Voltage below normal or shorted to lower voltage. Current below normal or open circuit.
What is the SPN code for a FMI Sid?
SPN FMI PID/SID PID/SID ID FLASH CODE FAULT DESCRIPTION 634 4 SID 40 1321 Constant Throttle Valve Circuit Failed Low 634 3 SID 40 1321 Constant Throttle Valve Circuit Failed High 634 5 SID 40 1321 Constant Throttle Valve Circuit Failed Open 636 1 SID 21 1235 Crankshaft Position Sensor Signal Voltage Too Low
What does SPN stand for on a diagnostic code?
Previously active diagnostic trouble codes can only be cleared by a service tool, such as Diamond Logic® Builder (DLB). Some previously active codes may not be cleared by this method. “SPN” represents the Suspect Parameter Number. This number identif es the item for which diagnostics are being reported. FMI” is the Failure Mode Indicator.
What is the engine coolant sensor code in FMI?
110 2 PID 110 1212 Engine Coolant Sensor (OUT), General Temp. Plausibility Error SPN FMI PID/SID PID/SID ID FLASH CODE FAULT DESCRIPTION 132 7 PID 132 1213 Intake Air Throttle Valve Closure Detection- Positive Torque 132 14 PID 132 1213 Intake Air Throttle Valve Closure Detection -Braking Condition
What is the SPN code for the fuel filter?
SPN Code: SPN Name: SPN Description: 16: Engine Fuel Filter Differential Pressure (see also SPN 1382) Differential pressure measured across the fuel filter located between the fuel tank and the supply pump. See SPN 1382 and Figures SPN16_A & SPN16_B. 18: Engine Fuel Pressure (Extended Range) 19: Engine Oil Pressure (Extended Range) 20
Which is the correct SPN 91 or 974?
NOTE—See SPNs 91 and 974 for additional accelerator position parameters. 30 Engine Crankcase Blowby Pressure 31 Transmission Range Position Not referenced in J1939-71 32 Transmission Splitter Position The current position of the splitter cylinder. 33 Clutch Cylinder Position Not referenced in J1939-71 36 Clutch Plates Not referenced in J1939-71 37
Where to find SPN code for 16 engine?
SPN codes description SPN Code SPN Name SPN Description 16 Engine Fuel Filter Differential Pressure (see also SPN 1382) Differential pressure measured across the fuel filter located between the fuel tank and the supply pump. See SPN 1382 and Figures SPN16_A & SPN16_B.
Which is the best SPN for an 82 engine?
It is recommended that SPN 3609 be used as it has better resolution. 82 Engine Air Start Pressure Gage pressure of air in an engine starting system that utilizes compressed air to provide the force required to rotate the crankshaft.
What are the fault codes for MaxxForce 15?
International MaxxForce 15 (All Years) Fault Codes CODE DESCRIPTION SPN 27 FMI 0 EGRP fault: over temperature SPN 27 FMI 3 EGRP signal Out of Range HIGH SPN 27 FMI 4 EGRP signal Out of Range LOW SPN 27 FMI 7 EGRP does not agree with commanded posit
Why is my MaxxForce 10 spn102 so slow?
Called and spoke with the local dealer and they said when they see this code they replace the IMP (intake manifold pressure) sensor and if still has the issue the remove both turbos to clean carbon off from them, Anyone else run into this before? Turbo “coking” is very common and can cause slow or lazy boost build.
How did I Fix my MaxxForce 10 fmi10 Turbo?
Ended up taking the compressor side of the turbos off and cleaning them, international had a service bulletin on it. They were pretty gummed up.
What is the SPN code for a FMI PID?
SPN FMI PID/SID PID/SID ID FLASH CODE FAULT DESCRIPTION 132 7 PID 132 1213 Intake Air Throttle Valve Closure Detection- Positive Torque 132 14 PID 132 1213 Intake Air Throttle Valve Closure Detection -Braking Condition 132 14 PID 322 1635 HC-Doser Fuel Pressure Not Plausible 132 1 PID 322 1213 Air Mass Flow Too Low
What is the FMI for a Cummins SPN 102?
Yeah right, I am the warranty!!! I get for SPN:102,FMI:18 — cummins fault code 125 — Intake Manifold 1 Pressure – Data Valid But Below Normal Operating Range – Moderately Severe Level. Intake manifold pressure is below the minimum operating limit.
Which is j-1939 fault code source address?
SS 1033423 : J-1939 Fault Code Source Address (SA), Suspect Parameter Number (SPN), and Failure Mode Indicator (FMI) Descriptions 1 SS 1033423 : J-1939 Fault Code Source Address (SA), Suspect Parameter Number (SPN), and Failure Mode Indicator (FMI) Descriptions