What is the fault code for an ECU?

What is the fault code for an ECU?

Engine ECU Faults (MID 128) Fault Code Description FMI Codes MID 128 PPID 326 Soot Level (DPF System) 0,11 MID 128 PPID 328 Aftertreatment Injection Shutoff Valve 3,4,5,7,14 MID 128 PPID 329 Aftertreatment Fuel Injector 3,4,5,7,14 MID 128 SID 254 Engine electronic control unit (EECU) 3, 8, 12

What is the fault code for a mid 128 engine?

Engine ECU Faults (MID 128) Fault Code Description FMI Codes MID 128 PID 26 Engine Fan Speed Percent 3,8 MID 128 PID 27 EGR Valve #1 Position Sensor 3,4,5 MID 128 PID 45 Preheater Relay Status 3,4,5 MID 128 PID 81 Particulate Filter 0,2,3,5,12

What does FMI 14 mean for Volvo Vecu?

FMI 14 The vehicle control unit (VECU) does not receive information from the adaptive cruise control unit (ACC) via the SAE J1939 data channel. Breaking or partial damage to the data channel. The ACC unit may be faulty.

What does FMI stand for in PID and mid?

Now that we have defined MID (The component) and PID (types of data), we can talk about Failure Mode Identifiers (FMI). Every diagnostic trouble code (DTC) that you find will have a FMI. This code is set by the ECM detecting a variety of problems, such as too much voltage, not enough voltage, resistance is in correct, and so on.

What can cause a 231 data link fault?

Thanks for the information Michael. The 231 data link faults can be caused by three things. The first and most common is faulty wiring between the engine ECM and the device. Devices like vehicle speed, clutch, brake, and dash items that are on the J1939 circuit.

Where are the codes 231-2 and 231-14?

I though the codes were in the engine ECM. The 231-2 code on the Bendix side is defined as Engine Data link error. The 232-14 is defined as ECU fault. I suspect you may have a problem with the Bendix unit. The reason I say this is because you have no codes in the engine ECM. If there was a problem in the engine ECM, you would have seen a code.

What is the 231-2 code on the Bendix side?

The 231-2 code on the Bendix side is defined as Engine Data link error. The 232-14 is defined as ECU fault. I suspect you may have a problem with the Bendix unit. The reason I say this is because you have no codes in the engine ECM. If there was a problem in the engine ECM, you would have seen a code.

How to clear an aftertreatment fault code?

Use the reset tool to clear aftertreatment codes! Short circuit to battery voltage, unit injector low side. Open circuit in actuator circuit. Mechanical system does not respond correctly. Resistance too high in injector. Ground. Slow PWM Valves Solenoid Valve. Power Take-Off 1 Solenoid Valve. Power Take-Off 2 Solenoid Valve. Brake, Counter Shaft

What is the fault code for a truck?

Short circuit to battery voltage, unit injector low side. Open circuit in actuator circuit. Mechanical system does not respond correctly. Resistance too high in injector. Ground. Slow PWM Valves Solenoid Valve. Power Take-Off 1 Solenoid Valve. Power Take-Off 2 Solenoid Valve. Brake, Counter Shaft

What does ECU 128 mean on a truck?

There is no charge for this service, but standard message and data rates may apply. It means that the engine ECU has a code in it. ECU 128 only identifies the module, it is not a fault code. Can you hit a dash button and get more numbers?

When did the SID number go blank on Freightliner?

If there is no text message, the display area will be blank. Only the SID number will display. * On March 7, 1997. If there is no text message, the display area will be blank. Only the SID number will display. * On March 7, 1997. If there is no text message, the display area will be blank. Only the SID number will display. * On March 7, 1997.

Where can I find the PID list for mid?

The entire PID list can be downloaded by filling out the form at the top of the page. It is approximately 11 pages total. Now that we have defined MID (The component) and PID (types of data), we can talk about Failure Mode Identifiers (FMI). Every diagnostic trouble code (DTC) that you find will have a FMI.

What does the fault code on the control panel mean?

† Stopping the motor (if it was on). The fault code on the control panel display is temporary. Pressing any of the following buttons removes the fault message: MENU, ENTER, UP button or DOWN button. The message reappears after a few seconds if the control panel is not touched and the fault is still active. 1-282 ACH550-UH User’s Manual Diagnostics

How to reset the engine control module ( ECU )?

The 2 most common ways to reset your car computer is by either unplugging the battery or by resetting the fuse related to the engine control module Will disconnecting battery reset ECU? Disconnect the battery and Switch the ignition key to the on position for about 15 minutes should reset the ECU

What are the symptoms of a bad ECM power relay?

A bad relay may cause the vehicle to crank, but not start, or sometimes not even crank at all. 3. Battery drain or dead battery. A failed ECM power relay can also cause a battery drain or dead battery. If the relay shorts it can leave power on to the computer, even when the vehicle is turned off.

What should I do if my ECU light comes back on?

Drive the car for at least 10 miles for the ecu to learn, if there is a problem with your vehicle then the check engine light will come back on and you can analyze the fault code that the ECM throws. These codes will guide you towards the root of the problem and you can begin replacing parts to try to fix the issue.

Is there a mid 128 PID 84 FMI 2?

Mid 128 pid 84 fmi 9 Mid 144 pid 84 fmi 2 Mid 144 pid 205 fmi 9 Transmission goes to operation failed so I can’t get any codes…  read more Roy Belding 7,687 satisfied customers

What is the fault code for 84fmi 2?

EFFECT Fault Code: 241PID: P084SPN: 84FMI: 2/2LAMP: AmberSRT: Vehicle Speed Sensor Circuit – data incorrect. The ECM lost the vehicle speed signal. Engine speed limited to maximum engine speed without VSS parameter value.

Posted In Q&A