What is the low coolant level sensor on a Cummins?

What is the low coolant level sensor on a Cummins?

Cummins ISB and ISC, Low Coolant Level Sensor 54-265 General Information The three-wire low coolant level sensor (CAS 700685 001) on some M2 vehicles built from 2007 to October 8, 2009, with Cummins ISB and ISC engines, may develop an internal leak, causing the engine light to illuminate and the engine to shut down.

What is the fault code for a ghg14 truck?

1 FAULT CODE DESCRIPTION GHG14 108 13 Ambient Air Pressure Signal Not Available via CAN 110 9 Coolant Temperature Signal Not Available via CAN 158 7 ACM Power Down – Key Off Purge Cycle 168 0 Battery Voltage High 168 1 Battery Voltage Low 171 13 Ambient Air Temperature Signal Not Available via CAN

Why is the coolant not flowing to the radiator?

The engine coolant temperature does not reach to specified temperature even though the engine has run long enough. The thermostat is a component that blocks the flow of coolant to the radiator until the engine has warmed up. When the engine is cold, no coolant flows through the engine.

What are the ISM fault codes for Cummins?

Intake Manifold 1 Pressure Sensor Circuit – Voltage Below Normal or Shorted to Low Source. Low signal voltage or open circuit detected at the intake manifold pressure circuit. Intake Manifold 1 Pressure – Data Valid but Below Normal Operating Range – Moderately Severe Level. Intake manifold pressure is below the minimum operating limit.

What is the ISC Code for a Cummins solenoid?

322 Injector Solenoid Driver Cylinder 1 Circuit – Current Below Normal, or Open Circuit 323 Injector Solenoid Driver Cylinder 5 Circuit – Current Below Normal, or Open Circuit

What is low signal voltage at engine coolant level?

Low signal voltage detected at engine coolant level circuit Coolant Level – Data Valid but Below Normal Operational Range – Moderately Severe Level. Low engine coolant level detected. Engine Oil Temperature Sensor 1 Circuit – Voltage Above Normal or Shorted to High Source.

When to change coolant on a Cummins ISC 8.3?

Allow engine to cool 20-30 minutes and drain again. Repeat until the effluent color is clear. At this point, if this is the first coolant change on a 2-3 year old coach and you are not changing coolant brands/types, skip right to “Last rinse”. For older systems or when switching types of coolant, add a Cooling System Cleaner. Follow the directions.

Where can I get genuine Cummins ISC parts?

Find more genuine cummins parts from China. HEXAGON FLANGE HEAD CAP SCREW – B5.9-M210 / ISC / B5.9M / 6B5.9 / 4B3.9 V-BELT – 4BT / 6BT / ISB / 6CTA 8.3L (69 IN.) Cummins exhaust manifolds for 8.3 ISC, 6CTA, and QSC diesel engines. Have any question, Please enter the form below and click the submit button.

Do you have a 1999 Cummins 8.3 ISC?

I have a 1999 cummins 8.3 isc in a freightliner fl70. It will not start I have check for fuel delivery and its good. There is also fuel from the pump to the injector. But the I jector is not opening o … read more

What is the part number for a Cummins Engine?

You are buying a brand new part number 4921485 OEM Cummins (Rectarngular Oval .. NEW Coolant Level Sensor & Most Make Trucks with a Cummins EngineYou are buying a brand new Repl.. You are buying a brand new Cummins M11 & N14 CelctPlus ECM SENSOR “A” Conn..

What kind of oil temperature sensor does Cummins use?

You are buying a brand Cummins L10, M11 & N14 Oil Temperature Sensor 38653.. You are buying (1) brand new part number 3803682 Cummins Injector Pigtail Kit (All L.. You are buying a brand New Cummins L10, M11 & N14 Celect & CelectPlus (New ..

Where can I buy a Cummins HDP test kit?

You are buying a brand new HDP Electronic Test Kit for all Cummins L10, M11 &a.. 3073926 Cummins L10 & M11 Celect (Prior to 1996) External Engine Sensor Wiring Harness No Ambient Sensor Plug. You are buying a 3073926 Cummins L10 or M11 Celect (Prior to 1996) Sensor External Engine W..

Posted In Q&A