Why are my brake lights not working on my 1997 Chevy?

Why are my brake lights not working on my 1997 Chevy?

Pull the plastic cap off the fuse chassis and you’ll see a square relay fuse switch and replace it for the brakes. It’s only $13 bucks and is the predominant issue with 1997 Chevy Trucks and the brakes not working especially if you reverse and blinker lights do work. Was this answer helpful? Its the taillight circuit board or a broken wire.

What to do if there are no brake lights?

Cut repair costs, not quality. Here is some info for you. Fuse No.1 is for your brake lights and your hazard lights. If no lights after fuse, if found blown, is replaced check your light globes. If nothing works check that the fuse hasn’t blown again. Fuse 16 is for the turn lights.

Why does my brake light work when I Turn on the turn signal?

For that to work, the brake wire runs to the turn indicator, so that when you turn on the flashing turn signal, it switches out the brake light signal for that side so that the two signals don’t collide. So don’t just check the brake light. Also check the turn signals.

Where are the brake lights on my car?

You will get the fuse panel under the dashboard and the PDC under the hood. The brake light switch is also to be found under the dashboard and check if its plunger touches the brake pedal arm. Any problem with the fuse box and light switch will affect the brake lights.

Pull the plastic cap off the fuse chassis and you’ll see a square relay fuse switch and replace it for the brakes. It’s only $13 bucks and is the predominant issue with 1997 Chevy Trucks and the brakes not working especially if you reverse and blinker lights do work. Was this answer helpful? Its the taillight circuit board or a broken wire.

Cut repair costs, not quality. Here is some info for you. Fuse No.1 is for your brake lights and your hazard lights. If no lights after fuse, if found blown, is replaced check your light globes. If nothing works check that the fuse hasn’t blown again. Fuse 16 is for the turn lights.

For that to work, the brake wire runs to the turn indicator, so that when you turn on the flashing turn signal, it switches out the brake light signal for that side so that the two signals don’t collide. So don’t just check the brake light. Also check the turn signals.

Why are the brake lights not working but the tail lights are?

Blown out light bulbs are the most common reason for why the brake lights not working but the tail lights are. Remove the screws from the bulb lens (which you can access through the trunk or see your vehicle repair manual to get the exact location). Push the bulbs and turn them counterclockwise to remove from the socket.

Where are the brake lights on a C / K 1500?

There is a switch. I think on most C/K 1500/2500 it is on the brake pedal arm or the arm hits it. It is $5-$10; you might take ALL your truck data to the auto parts store, buy a new switch, then look for the same thing around the brake arm or under the hood. There’s a fuse. Find the fusebox and look for “brake”. The Owner’s Manual may have clues.

Where do the brake lights go in a car?

The way those taillights work theres a white wire under dash on the column that white wire is for brake light. So the way the brake lights work they go through a relay and through blinker switch.

What should I do if my brake lights dont work?

Solder and shrink tube the new wire to these pigtails and give it a test. If you are unsure of the wire color associated with brake light function, you can access wiring diagrams online, but be warned, chev/gm have been known to change color codes from time to time.

Why are the rear lights on my car not working?

The most common reason rear lights of any kind will fail is rotted wires. They run through wire shroud from front to back along the inside of the frame to the left tail light. Running this way leaves them exposed to the elements. Check along the run for rotted, broken or degraded wire.

Where are the fuses on a GMC Vandura?

Fuse box diagram (fuse layout), location, and assignment of fuses GMC Vandura G1500, G2500, G3500, and Chevrolet Van G20, G30 (1988, 1989, 1990, 1991, 1992). The wiring circuits in your vehicle are protected from short circuits by a combination of fuses, circuit breakers, and fusible links.

There is a switch. I think on most C/K 1500/2500 it is on the brake pedal arm or the arm hits it. It is $5-$10; you might take ALL your truck data to the auto parts store, buy a new switch, then look for the same thing around the brake arm or under the hood. There’s a fuse. Find the fusebox and look for “brake”. The Owner’s Manual may have clues.

The way those taillights work theres a white wire under dash on the column that white wire is for brake light. So the way the brake lights work they go through a relay and through blinker switch.

Why do my brake lights not work on my GMC Sierra?

I have a 1994 GMC Sierra C1500 2WD with 4.3l w/automatic. It was a fleet vehicle. Plain Jane accept for High Output Heater, Limited Slip Diff and Engine Block Heater. Brake lights were working intermittently. Would come on when pedal as first depressed then go out after pedal traveled down a bit. I put in a new switch and all was well for 3 months.

Why are the rear lights on my 91 k1500 not working?

I had the same problem on my 91 K1500. The most common reason rear lights of any kind will fail is rotted wires. They run through wire shroud from front to back along the inside of the frame to the left tail light. Running this way leaves them exposed to the elements.

How do you turn on the brake light on a Chevy Silverado?

Back probe the switch terminals with a test light. Only one of the switch terminals should turn on the test light. When you depress the brake pedal, both switch terminals should turn on the test light. If only one of the wires turns on the test light, unplug the switch and jump the two connections at the connector.

Is it dangerous to drive with brake lights not working?

Driving at night with either brake lights or tail lights not working is dangerous for you and other drivers on the road. It takes a long time to notice when the brake lights not working but tail lights are or vice versa. It is so because you won’t know what is happening in the backside while driving until someone points it out.

Why does my third brake light not work?

Jim, common problem. If your third brake light works either way but the rear brake lights stop working when the truck is on its a faulty ground wire to the stop lamp relay. Other things use that ground when the key is on so its not strong enough then to activate the armature within the relay.

Blown out light bulbs are the most common reason for why the brake lights not working but the tail lights are. Remove the screws from the bulb lens (which you can access through the trunk or see your vehicle repair manual to get the exact location). Push the bulbs and turn them counterclockwise to remove from the socket.

What to do if your brake lights are not working?

Ok, changed out turn signal switch and still have no brake lights. Again, i changed the bulbs, replaced the brake switch, and replaced the turn signal switch. The parking lights work, the blinkers work, the back-up light works, and the hazzards work. But still no brake lights.

Jim, common problem. If your third brake light works either way but the rear brake lights stop working when the truck is on its a faulty ground wire to the stop lamp relay. Other things use that ground when the key is on so its not strong enough then to activate the armature within the relay.

You will get the fuse panel under the dashboard and the PDC under the hood. The brake light switch is also to be found under the dashboard and check if its plunger touches the brake pedal arm. Any problem with the fuse box and light switch will affect the brake lights.

Why does my brake light only work on one side?

Since the problem is only on one side, you can rule out the fuse and other parts of the circuit that are shared by both bulbs. I would look closely at the connector for the nonfunctional bulb, as it may be damaged or corroded. If the bulb looks OK, you’ll want to test for power and ground at the bulb.

Why is my passenger side brake light not working?

The brake light (passenger side) went out. I replaced the bulb and the other one while I was at it. But the passenger side brake light still doesn’t work. Even tried switching bulbs to use the one that I knew was working on driver’s side, but still wouldn’t work on passenger side. I see that there’s only one fuse control for both lights.

The causes for dysfunctional rear lights are: 1 Burnt bulbs 2 Blown out fuse 3 Damaged wiring 4 Electrical issues

Why does the tail light stay on when the car is turned off?

There are many causes for tail light constantly staying on while the car is turned off: A broken brake light switch, damaged trailer light plug, faulty brake light switch stopper, broken wiring harness,… There are various reasons, however, you can check whether it is the brake lights or the tail lights to see which are the parts having problems.

What should I do if my brake light is not on?

Before you replace the turn signal switch assembly, be sure the hazard switch is fully turned off and is not stuck midway between on and off. To verify this, check for 12 volts on the white wire, (blue arrow), at the signal switch connector when the brake pedal is pressed.

Where is the fuse on the brake light?

You will get the fuse panel under the dashboard and the PDC under the hood. The brake light switch is also to be found under the dashboard and check if its plunger touches the brake pedal arm. Any problem with the fuse box and light switch will affect the brake lights. In case if the fuse is blown, change it with a new one.

Wal-Mart and any parts store will keep them in stock, usually at $10 or less. Just hook the clip of the light up to a good ground and touch the two metal tabs on top of the fuse. There is no need to pull the fuse for this. It should be “hot” on both sides. If it is not, replace the fuse.

Why does my brake light fuse keep blowing?

Another bulb related fault occurs if the filaments in a dual filament bulb short together. If the problem is not found in the bulbs or contacts, basically any wire, ground, or component in the fused circuit is a possible cause. Failures can often be simple insofar as cause so of course check the bulbs and terminals carefully first.

You will get the fuse panel under the dashboard and the PDC under the hood. The brake light switch is also to be found under the dashboard and check if its plunger touches the brake pedal arm. Any problem with the fuse box and light switch will affect the brake lights. In case if the fuse is blown, change it with a new one.

Why are my tail lights not working but brake lights are working?

Burnt out light bulbs – The other reason your tail lights are not working but your headlights are maybe a blown bulb. When the filament inside the bulb breaks it cannot illuminate the gas enclosed within the glass cover. This burnt-out bulb does not affect the circuitry of the light system and it continues to function normally.

What kind of parking brake does a 2000 Kodiak have?

Hello, we have a 2000 C6500 Kodiak with a parking brake problem. The truck has a Cat engine, AT, and hydraulic brakes. The parking brake is the electric over hydraulic type that activates a tranny mounted drum brake. The shoes are in good condition yet and adjustments are fine.

Posted In Q&A