Why does my car not start with a new crankshaft sensor?

Why does my car not start with a new crankshaft sensor?

A new crankshaft sensor should not have prevented the vehicle from starting. The cause of the no start issue is either related to a fuel or ignition issue that the vehicle has or something that happened during the replacement of the crank sensor.

How do you replace the crankshaft position sensor?

1. Disconnect the crankshaft position (CKP) sensor electrical connector (3). 2. Remove the starter. 3. Remove the CKP sensor bolt. 4. Remove the CKP sensor. 1. Lubricate the CKP sensor O-ring seal with clean engine oil. 2. Install the CKP sensor.

Why does my car not start when I push the start button?

False input or lack of input from sensors like the crankshaft position sensor (CKP) or camshaft position sensor (CPS) can prevent the engine from starting. Also, a bad throttle position sensor (TPS) may cut off the spark to the cylinders.

What to look for when your engine won’t start?

Check for a blown fuse that may be preventing a circuit from working properly, like the fuel injection or computer system. To operate efficiently, an internal combustion gasoline engine needs a good spark, the right amount of fuel, and good compression (a healthy mechanical condition).

Why does my car not start after replacing the crankshaft position sensor?

I changed out the crankshaft position sensor on my car because it was losing power while driving and the code on an AutoZone scanner said crankshaft position sensor. After replaced with a new one, car had a rougher start, no loss of power but now, two days later, it won’t start at all.

What happens to the crank sensor on a GMC?

The crankshaft sensor on GMC vehicles is synced to the powertrain control module, or PCM. When the crank sensor is replaced, it must be resynced to the PCM. Without resyncing, the PCM cannot properly determine the position of the crankshaft.

False input or lack of input from sensors like the crankshaft position sensor (CKP) or camshaft position sensor (CPS) can prevent the engine from starting. Also, a bad throttle position sensor (TPS) may cut off the spark to the cylinders.

Where do I find the crankshaft position sensor?

Just take off the Fly wheel again and look at the inner most circle on the inside of the fly wheel. You will see a groove on the inside of the circle. You will see a matching finger on the engine block where the wheel mounts that matches the groove on the wheel.

Why does my car not start when I Turn on the engine?

False input or lack of input from sensors like the crankshaft position sensor (CKP) or camshaft position sensor (CPS) can prevent the engine from starting. Also, a bad throttle position sensor (TPS) may cut off the spark to the cylinders. Battery.

What would make your Car Crank but not start?

When your engine cranks but won’t start or run, it could mean your engine is having trouble producing a spark, getting fuel, or creating compression. The most common causes are in the ignition (for example, a bad ignition coil) or fuel system (for example, a clogged fuel filter).

What causes no crank no start?

With a no crank/no start condition, the first thing to check is the battery. The battery or battery problems are the number-one cause of this type of no-start condition.

Why does it crank but not start?

In layman’s terms, a No Start Condition means that your vehicle’s starter motor is cranking the engine but the engine is not starting. This condition is usually due a failed fuel pump, a failed ignition coil, a failed ignition control module, a failed crank sensor, etc… that lets the engine crank (turn over) but does not let it start.

Will the crank sensor cause my car not to start?

The crank sensor can definitly cause the engine not to start, but it has to be diagnosed thru a factory level scan tool or automotive oscilliscope . So we can determine if it may be at fault, by testing some basics.

Can a camshaft sensor cause a car not to have spark?

The advantages to such a system include the absence of a rotor or distributor cap, which may burn or crack with use, along with the absence of a vacuum advance diaphragm, which can rupture or leak. But when a camshaft position sensor takes the place of a distributor, failure of that sensor could result in there being no spark.

What causes a car not to have spark?

But when a camshaft position sensor takes the place of a distributor, failure of that sensor could result in there being no spark.

What happens if the camshaft position sensor is not working?

In such a case, the computer would calculate the need for spark advance (when the spark plug fires sooner in the compression stroke than otherwise) to be almost maximum. But if the camshaft position sensor is not working, the car’s computer cannot know when to fire the ignition coils to achieve the desired advance.

Can a failed crank sensor cause no start?

The thing to remember about having a failed crank sensor, is that if you have spark or fuel injector pulses, the crank sensor is OK and not the cause of your No Start Condition. The crankshaft position sensor, on your 4.8L, 5.3L, 6.0L GM vehicle, is a Hall-Effect three wire crankshaft position sensor.

How many times does a crank sensor spark?

One wire delivers power in the form of 12 Volts from the PCM. Another delivers Ground. This Ground is provided inside the PCM, too. As the engine turns, a reluctor wheel on the crankshaft activates the crank sensor into creating its On/Off voltage signal 24 times per crankshaft revolution. Activate the 8 COP coils to spark.

What happens when you replace the crankshaft sensor?

Q: Replaced crankshaft sensor and now car won’t start. Even tried putting old one back and still won’t start. No problem starting bef Was told my crankshaft sensor needed replacing. Car was running bad. Shop ran codes and came up with crankshaft sensor. I replaced it with a new one now car won’t start.

Why is my cam sensor still no spark?

Just replaced cam sensor still no spark 2 people found this helpful. did you check codes and fuel pressure. 1 people found this helpful. Have good fuel pres. I do have a theft deterrent code not sure what that is 1 people found this helpful. what i meant was computer codes 1 people found this helpful.

The crankshaft sensor on GMC vehicles is synced to the powertrain control module, or PCM. When the crank sensor is replaced, it must be resynced to the PCM. Without resyncing, the PCM cannot properly determine the position of the crankshaft.

Can a crank and cam sensor be replaced?

I replaced both the cam and crank sensor and car still will not start but if I unplug the crank sensor it starts up and runs like crap. I can not figure out what to do next. My car has 91000 miles. My car has an automatic transmission. You should check to see if your vehicle has jumped timing.

Why does my car have the wrong ignition timing?

Have a mechanic verify that the camshaft timing did not jump after scanning and looking at the crankshaft sensor data to verify it is giving a signal. If it is giving a signal, then the cam and crank signals are way off and causing the wrong ignition timing.

A new crankshaft sensor should not have prevented the vehicle from starting. The cause of the no start issue is either related to a fuel or ignition issue that the vehicle has or something that happened during the replacement of the crank sensor.

Is the Jeep Grand Cherokee 4.0 with no start?

Come along with Eric O. at SMA as he has a look at this 2001 Jeep Grand Cherokee with the I6 4.0 that was towed in with a crank, no start condition. It didn’t take long to figure out this common problem and solve the infamous P0320 crank sensor code.

What is the average crankshaft position sensor rating?

Average rating from 129,829 customers who received a Vehicle Engine Electrical Inspection. The crankshaft position sensor is an engine management component found on virtually all modern vehicles with internal combustion engines.

What does the crankshaft position sensor do on a car?

All the modern vehicles have the crankshaft position sensor. It is a component for monitoring the crankshaft’s rotational speed and position. It also sends a report to the engine control unit so that the latter can make the right adjustments should anything is malfunctioning.

What causes a misfiring cylinder on a crankshaft?

Misfiring cylinder is a common response to sensor problems. It’s a common response when your car experiences some crankshaft position sensor symptoms. Failing sensor cannot provide correct information about the piston position, causing one of the cylinders to misfire. An issue with the spark plug will also draw the same response.

Can a bad sensor cause a cylinder to misfire?

Failing sensor cannot provide correct information about the piston position, causing one of the cylinders to misfire. An issue with the spark plug will also draw the same response. However, if the problem persists after handling all the other issues, the sensor is likely to be the culprit.

What causes the fuel pump to not start?

The fuel pump is running and delivering normal pressure to the engine But, with all that working your engine still will not start. So, the most likely cause, is that the fuel injectors are probably not opening. The (PCM) uses the trigger signal from the crankshaft position sensor; and/or camshaft position sensor to pulse the injectors.

What should I do if my car cranks but no start?

All my research pointed towards the Crank Shaft Position sensor fixing this, especially since it was stalling a low speeds, and now has no spark or fuel injector pulse. The mechanic I’ve been working with the last 2 days wants to try replacing the Crank Shaft Angle Sensor/Trigger Plate/Crank Shaft Angle Plate, whatever it’s called.

What makes an engine not start or run?

All engines require three things to start and run: spark, fuel and compression. If any one of these is missing, your engine will not start. The fuel pump is running and delivering normal pressure to the engine

The fuel pump is running and delivering normal pressure to the engine But, with all that working your engine still will not start. So, the most likely cause, is that the fuel injectors are probably not opening. The (PCM) uses the trigger signal from the crankshaft position sensor; and/or camshaft position sensor to pulse the injectors.

Can a bad crank sensor cause fuel pump failure?

The lack of signal could also prevent the fuel pump relay from activating and priming the fuel lines. But I’m struggling to buy that a bad crank position sensor would result in physical failure of the fuel pump.

All my research pointed towards the Crank Shaft Position sensor fixing this, especially since it was stalling a low speeds, and now has no spark or fuel injector pulse. The mechanic I’ve been working with the last 2 days wants to try replacing the Crank Shaft Angle Sensor/Trigger Plate/Crank Shaft Angle Plate, whatever it’s called.

What causes a Mercedes Benz engine to not start?

Engine Cranks but no Start, Dies, Stalls, or Backfires. A failed crankshaft position sensor can cause your engine to stall or not start at all. Your Mercedes-Benz may start and run for a short time, or until it gets warm and then it dies.

How do you replace a CPS sensor on an engine?

Back of engine, near the firewall. Unplug the electrical connector from the CPS sensor. Squeeze the connector and pull it away from the CPS sensor. Remove bolt. Remove the crankshaft position sensor. You will have either an E8 or E10 bolt that holds the CPS sensor in place. Install new sensor.

How much does it cost to repair a Mercedes no start crank?

The cost to complete this repair yourself is under $80 vs. $400 at a shop. You will need one to two hours to make this repair if you are performing this job for the first time. In this repair guide, we will show you how to replace the CPS yourself.

Engine Cranks but no Start, Dies, Stalls, or Backfires. A failed crankshaft position sensor can cause your engine to stall or not start at all. Your Mercedes-Benz may start and run for a short time, or until it gets warm and then it dies.

What happens when you crank the engine but it does not start?

The engine may crank, but it will not start. You may need to crank the engine longer in order to get it to start. Failed crankshaft position sensor can also impact the idling, the acceleration, or even your transmission shifting. In some cases, it can cause your transmission to go into limp mode.

What are the symptoms of a failed crankshaft sensor?

Other symptoms of a failed crankshaft position sensor are poor acceleration, engine vibrations, poor throttle response, bad fuel economy, hesitation, engine stalls. The engine starts if you let it cool down. If you are stuck on a parking lot and the car will not start, let the car cool down at least 30 minutes and then try again.

Back of engine, near the firewall. Unplug the electrical connector from the CPS sensor. Squeeze the connector and pull it away from the CPS sensor. Remove bolt. Remove the crankshaft position sensor. You will have either an E8 or E10 bolt that holds the CPS sensor in place. Install new sensor.

Why is my crank sensor not working on my Opel Corsa?

WONT START replace the crank sensor – YouTube OPEL CORSA. WONT START replace the crank sensor If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations.

What to do if your crankshaft sensor is not working?

Issues with the crankshaft sensor can quickly lead to problems that affect the drivability of the vehicle. For this reason, if you suspect your crankshaft position sensor has an issue, have the vehicle inspected by a professional technician right away. They will be able to diagnose your car and replace your crankshaft position sensor if necessary.

WONT START replace the crank sensor – YouTube OPEL CORSA. WONT START replace the crank sensor If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations.

Why does my car not start when I crank the engine?

If the engine doesn’t crank, or makes an unusual noise when cranking, you may have a starting system problem. The car’s security system may have made an error that disabled the fuel or ignition system, or the chip in the key may have failed.

What is the code for a bad crankshaft position sensor?

A diagnostic scan tool will show a code between P0335 and P0338. The check engine light doesn’t always come on, though, so you could be experiencing any of the above symptoms for some time before you see the warning light. There are a number of different problems that can cause similar symptoms to a crankshaft position sensor problem.

Why is the Check Engine light not coming on?

Even if the check engine light hasn’t come on, you may find a pending code that can guide you in your diagnosis. False input or lack of input from sensors like the crankshaft position sensor (CKP) or camshaft position sensor (CPS) can prevent the engine from starting.

What to do if your crankshaft sensor is bad?

If your crankshaft sensor is bad and your car won’t start, then this post on how to start a car with a bad crankshaft sensor will guide you from start to finish. This a step by step guide of what to do to get the car started again.

Why did my car not start after I replaced the sensor?

If you disconnected the battery before replacing the sensor, this could be one cause of the vehicle not to start. A new crankshaft sensor should not have prevented the vehicle from starting.

How does the crank sensor work on a car?

How the crank sensor branches off the troubleshooting tree varies from model to model. On most cars, it’ll affect both spark and injector firing, but on others, the ECU must see the crank signal in order for the fuel pump to run at all.

Why does my car not start when I Turn on the ignition?

The most common causes are in the ignition (for example, a bad ignition coil) or fuel system (for example, a clogged fuel filter). However, the source may also be a mechanical fault (for example, a leaking valve), or faulty components in other systems.

What makes an internal combustion engine not start?

To operate efficiently, an internal combustion gasoline engine needs a good spark, the right amount of fuel, and good compression (a healthy mechanical condition). The lack of any of these three things will prevent your engine from starting.

What should I do if my engine won’t start?

You should see a bright spark jumping the gap in the spark tester. If you don’t see a spark, repeat the test. This time, adjust the spark tester to 30KV. If you still don’t see a spark, repeat the test and set the tester to 10KV. If this time you see a spark or no spark, you have a problem with the ignition system.

Is there a problem with my Nissan Titan?

Titan has been running fine. I hadn’t noticed and issues until this morning. When I went to start it, it would turn over, but wouldn’t start. I’ve read through a few threads, and here’s what I’ve tried so far:

How to get off the bed of a Nissan Titan?

Bed was pretty easy to get off. 4 bolts, 2 brake light harnesses, in bed power plug harness, hose connected to evap canisters, fuel filler hose, and whatever the little hose is beside the fuel filler. There were 5 of us that lifted it.

What kind of fuel pump does a Nissan Titan use?

It wouldn’t start with a jump but as soon as I got a new battery it started.It would just sit there and crank and test right on the meter. It was the fuel pump again. The airtex e8595m I put in only lasted 2.5 months. I had to put another one in because it was the only pump I could find in town.

How does the crank position sensor work on a Nissan Titan?

The Nissan Titan utilizes a crankshaft position sensor in order to regulate the engine timing. This sensor uses a reluctor to gauge the position of the crank. When the Titan’s ECM determines that there is an issue with the signal coming from this sensor, it’ll throw the P0335 trouble code.

What does trouble code p0335 mean on a Titan?

When the Titan’s ECM determines that there is an issue with the signal coming from this sensor, it’ll throw the P0335 trouble code. Depending on the model year and engine of any vehicle the job of the crankshaft sensor is going to change.It’s either going to provide info to the ECM to keep the vehicle from misfiring.

How does the crank sensor work on a Toyota Tundra?

The crank sensor operates by scanning a “reluctor wheel”. This wheel can become damaged over time and will no longer give a proper reading to the ECM. One of the most common symptoms of a bad reluctor ring is going to be a rattling sound. If the engine still runs, you will hear it. This means that it has been damaged, and no longer seated properly.

What to do if your Nissan Sentra won’t start?

You need to check the fuel inertia switch in the right passenger kick panel to make sure it is not tripped. If not tripped, then check that the pink wire in and out has power when you crank the engine…. The 2015 Nissan Sentra is equipped with a CVT transmission.

Why is my car not starting after replacing the fuel pump?

Code P0335 relates to the camshaft position sensor not transmitting a proper signal to the PCM. The camshaft position sensor measures the rotational position of the camshaft and transmits that information to the engine control computer.

Why does my Nissan Maxima engine not start?

There are a lot of issues that can cause your Maxima to crank, but not start. The engine needs air, fuel, and a spark in order to run. It is highly likely that if the engine is cranking, but not starting that it has thrown an OBDII code. It is definitely worth it to use an OBDII scanner to check and see if the engine has thrown any trouble codes.

You need to check the fuel inertia switch in the right passenger kick panel to make sure it is not tripped. If not tripped, then check that the pink wire in and out has power when you crank the engine…. The 2015 Nissan Sentra is equipped with a CVT transmission.

What to do if your car wont start after replacing the fuel pump?

Car won’t start even after I replaced the fuel pump. Car won’t start and turned off while driving. Replaced the fuel pump and I can hear it working. The car still won’t start.

Why is my car turning over but not cranking?

Replaced it today, and the car is still turning over but not cranking. The timing is set right, its getting gas, and its getting fire. What else could be causing it to turn over but not crank? Any help would be appreciated. Does it have compression?

What to do when your car won’t start or turn over?

If you’re not sure, turn on the headlights. When you try to start the car, the lights should either dim considerably or turn off completely. If they do, your ignition switch should be good. If not, the switch will need to be replaced. Bad Starter Connection: Corrosion can keep your battery from connecting.

How to fix engine that wont Crank over axle?

1 Jack up the car and secure it with jack stands 2 Disconnect the battery 3 Count the number of shims the starter uses 4 Disconnect the wires at the starter 5 Gather all the necessary tools

What will cause your car not to turn over?

  • Dead Battery. Just because you have a dead battery today doesn’t necessarily mean that you have to go out and buy a new one.
  • Dirty Cables.
  • Bad Starter.
  • Further Troubleshooting.
  • Electrical No-Start Problems.
  • Ignition System Troubleshooting.
  • Fuel System Troubleshooting.
  • Other Issues That Might Prevent Your Car Starting.

    What all can cause a car not to crank?

    Problems That May Cause a No-Crank Condition Undercharged or failed battery Corroded or damaged connectors or wires Bad camshaft or crankshaft sensor Failed starter motor or solenoid (relay) Bad ignition switch Bad or misadjusted neutral safety switch Engine mechanical problems

    Why won ‘ t my car turn over?

    Possible Causes That a Car Won’t Turn Over. 1. This is the most likely problem, but it doesn’t mean you have to go and buy a new battery right away. Batteries can lose charge because of power drain, especially if you accidentally leave the headlights on overnight, causing your car not to turn over in the morning.

    Does your car turn over but won’t start?

    There may be occasions when your car turns over but won’t start. Basically, an engine needs three things to run smoothly – fuel, spark and compression. The engine depends on several other things to run smoothly such as fuel, ignition systems, etc.

    Why does my car not start when I change the cam sensor?

    Most of the time, this code comes up when there is a difference between the crank and cam sensors. The most common failure is the crankshaft position sensor. These fail much more frequently than the cam sensor and will cause a no start. It can also occur if the timing belt broke or jumped a tooth.

    Why does my car still won’t start?

    Changed camshaft sensor but car still won’t start, could Q: Changed camshaft sensor but car still won’t start, could it be the crankshaft sensor? Car is getting p0340 code changed camshaft position sensor.still won’t start could it be crankshaft sensor. It’s getting fuel and spark from the plugs.

    Most of the time, this code comes up when there is a difference between the crank and cam sensors. The most common failure is the crankshaft position sensor. These fail much more frequently than the cam sensor and will cause a no start. It can also occur if the timing belt broke or jumped a tooth.

    Can a bad crankshaft sensor cause a cylinder to misfire?

    Should you feel or hear a brief stutter in the engine, it may be a sign of misfiring cylinders from a bad crankshaft position sensor. A failing crankshaft position sensor cannot provide the right information about piston positioning in the engine, causing a cylinder to misfire.

    I replaced both the cam and crank sensor and car still will not start but if I unplug the crank sensor it starts up and runs like crap. I can not figure out what to do next. My car has 91000 miles. My car has an automatic transmission. You should check to see if your vehicle has jumped timing.

    Why does my GM car say no start no crank?

    How to diagnose a no start no click on GM vehicle. If you have a late model GM vehicle and turn the key only to hear nothing, you’ll most likely think you have a dead battery—and you may. But a no start, no crank, no click condition can be far more involved than that.

    What should I do if my car wont crank?

    With the key in the RUN or ACC position, see if you are getting power to fuses 5, 8, 10, and 14. If you aren’t getting power there, check fuse 18 and see if it’s good.

    Why does my Car Crank but not start?

    If it cranks but does not start, sometimes a temperature sensor is bad and the computer can’t figure out the proper amount of fuel to inject. Just a little off and the engine won’t start.

    Why is my car not starting with the remote?

    The remote starter shut off because you pressed the brake pedal. You instinctively turned the key to start, and nothing happened. Then, after you tried it a few more times, you decided to remove the key, and that didn’t work either. The vehicle is not starting because you forgot to put it back into park.

    What does it mean when your car won’t restart?

    And–most important of all–does “won’t restart” mean that the starter fails to activate when you turn the key, or does it mean that the starter cranks the engine but the engine does not start and run on its own? Since it’s intermittent and unlikely to be tested while malfunctioning, I would guess ignition module or crank position sensor.

    How to know if your engine has no spark?

    First Confirm Your Engine Has No Spark. 1 Disable the fuel system by removing the fuel pump fuse or relay. 2 Insert a spark plug tester into the plug boot and ground it on a piece of metal on the engine. 3 Finally, Have someone crank the engine and watch for spark.

    What to do when your car cranks but wont start?

    Use a multimeter to check the connectors on the fuel injectors. If the voltage isn’t measuring up, there is an issue with the connectors or the wiring. If you’re still having issues, check the crankshaft position sensor, the camshaft position sensor, or the throttle position sensor.

    What does no spark mean on an engine?

    No Spark: Engine Cranks, but No Spark. I Have Replaced Igniter, Engine cranks, but no spark. I have replaced igniter, coil pack, crank sensor. have the same problem?

    What to do if your car has no spark?

    Engine cranks, but no spark. I have replaced igniter, coil pack, crank sensor. have the same problem? I am assuming you have done all other checks for ignition as well as all underhood fuses. so try a security system reset if battery was disconnected would set it off and would not allow a start.

    What does the crank sensor on a GM 3.8L do?

    As the engine cranks, the ignition module receives the crank sensor signal. The crank sensor signal is an On/Off type of signal that can be measured with a multimeter or an LED Light.

    How does the crank sensor control the ignition module?

    The ignition module starts to turn On and Off the ignition coils in their proper firing order to create spark, after the crank signal arrives. This On/Off action is the Switching signal referred to above. Under 400 RPM’s, the ignition control module controls spark timing without the help of the fuel injection computer.

    Why does the crank sensor need 12 volts?

    And well, not only does it need the crank sensor signal, it needs 12 Volts and Ground. More specifically, it all starts when you turn the ignition switch (in other words: the key) to crank and start the car or truck (if you’re driving an Isuzu), and here’s what happens: The ignition module receives 12 Volts.

    What should I do if my car won’t start?

    I replaced it with a new one now car won’t start. Even if I put old one back, car still won’t start. No problem starting, before replacing sensor. My car has 20000 miles. My car has an automatic transmission. I would recommend retracing your steps.

    Why does my car not start when I plug it in?

    The cause of the no start issue is either related to a fuel or ignition issue that the vehicle has or something that happened during the replacement of the crank sensor. I would retrace your steps to make sure that everything is plugged in properly and if this does not work have the ignition and fuel systems tested.

    False input or lack of input from sensors like the crankshaft position sensor (CKP) or camshaft position sensor (CPS) can prevent the engine from starting. Also, a bad throttle position sensor (TPS) may cut off the spark to the cylinders. Battery.

    1. Disconnect the crankshaft position (CKP) sensor electrical connector (3). 2. Remove the starter. 3. Remove the CKP sensor bolt. 4. Remove the CKP sensor. 1. Lubricate the CKP sensor O-ring seal with clean engine oil. 2. Install the CKP sensor.

    Are there any cranks but no start issues?

    Thanks for doing this Bluebee..I didn’t realize how many “cranks but no start” issues affecting E39’s until I did searching..More so on E46. All of these problems are aproched the same way.. I want to check the fuses under here..How do I get this cap off without breaking anything? All of these problems are aproched the same way.. Click to expand…

    What to do if your car won’t start when you crank the engine?

    Remove a plug wire, insert a Phillips screwdriver or spare plug piece of bare wire into the plug wire boot and place the end near the engine block (do not hold the plug wire while cranking the engine unless you want a shocking experience). If there’s a spark when the engine is cranked, it has ignition. The problem is either fuel or compression.

    Average rating from 129,829 customers who received a Vehicle Engine Electrical Inspection. The crankshaft position sensor is an engine management component found on virtually all modern vehicles with internal combustion engines.

    I replaced it with a new one now car won’t start. Even if I put old one back, car still won’t start. No problem starting, before replacing sensor. My car has 20000 miles. My car has an automatic transmission. I would recommend retracing your steps.

    The cause of the no start issue is either related to a fuel or ignition issue that the vehicle has or something that happened during the replacement of the crank sensor. I would retrace your steps to make sure that everything is plugged in properly and if this does not work have the ignition and fuel systems tested.

    What to do if your riding mower won’t start?

    Riding Lawn Mower Wont Start? (Try this before buying a new battery) – YouTube If playback doesn’t begin shortly, try restarting your device. An error occurred. Please try again later. (Playback ID: 1JbnjBemow4xtK5g)

Posted In Q&A