Can a crankshaft pulley be removed from a Honda Civic?

The crankshaft pulley bolt is one of the most stubborn bolts on this era of Honda. Unfortunately, they also need to come off in order to remove the crankshaft pulley and the crankshaft seal behind it. Typically this is done in order to change the timing belt, but the crankshaft pulley itself will fail on its own as well.

What causes torque wrench to snap on Honda Civic?

Typically, you can feel it in your torque wrench if you’ve overtightened or stretched a bolt too far. An overtightened bolt will suddenly takes less effort to turn the bolt. When this happens, the head can often snap off, which means deal with an extremely tight bolt that can’t simply be unscrewed.

When to use new bolts on Honda Civic?

Manufacturers design bolts and screws to “stretch” when they’re install. That way, the bolt and screw threads firmly attach to the matching threaded hole or nut. This lowers or outright eliminates the risk that the bolt or screw will work itself loose. For the same reason it’s always a good idea to use new bolts when working on the engine.

How do you jack up a Honda Civic?

Use a two-post lift if that’s an option. If it’s not and you’re doing this in the driveway, just set the car up on jack stands. Remove the passenger’s side wheel. The crankshaft pulley is the single, large pulley at the bottom of the engine. Figure 1. Diagram of the jacking points. (Related Article: How to Jack Up Your Civic – Honda-Tech.com)

How many bolts and nuts are in a Honda Civic?

Here’s a list of bolts and nuts and their torque specifications for quick reference: description type count battery terminals nut 2 valve cover bolt 5 upper timing belt cover bolt 2 lower timing belt cover bolt 6

How do you unbolt a crank pulley bolt?

Attach a 17mm socket and attempt to unbolt the crank pulley bolt. In order for this to work, you’ll need an impact gun with more than 600 lb/ft of breakaway torque. If you have one handy, try it out. If it doesn’t work, then use a crank bolt removal tool. If the impact gun didn’t work, the next step is to use the crank bolt removal tool.

What kind of crankshaft does a Honda Civic have?

96-00 Honda Civic OEM D16Y8 Y7 crankshaft position sensor/crank gear. Only 1 left! Only 1 left! Only 1 left! The crankshaft of your Honda Civic auto is one of the essential parts of the vehicles engine.

Where is the harmonic balancer in an engine?

The crankshaft harmonic balancer is a device connected to the front of an engine’s crankshaft, usually built into the crankshaft pulley.

What to do if your crankshaft harmonic balancer is bad?

Separated harmonic balancer. For this reason, if you suspect that your harmonic balancer may be having an issue, have the vehicle inspected by a professional technician, such as one from YourMechanic. They will be able to determine if the vehicle needs a crankshaft harmonic balancer replacement.

What is the harmonic balancer on a Honda Civic?

This is a 2001 Honda Civic. This removal DIY will work on most Hondas from the mid 1990s until today. The “Harmonic Balancer” keeps the engine vibrations down. This is important in keeping the motor running smooth and not tearing itself apart. You are dealing with a 19mm bolt, which is called the “Crank Bolt”.

The crankshaft harmonic balancer is a device connected to the front of an engine’s crankshaft, usually built into the crankshaft pulley.

How to replace the crank pulley on a Honda Civic?

(Related Article: How to Jack Up Your Civic – Honda-Tech.com) If you’re lucky, you’ll be able to remove the bolt on this pulley by using just an impact gun. Attach a 17mm socket and attempt to unbolt the crank pulley bolt. In order for this to work, you’ll need an impact gun with more than 600 lb/ft of breakaway torque.

What’s the crank pulley removal tool for Honda?

Please enter a question. The Powerbuilt 648796 50-millimeter Honda crankcase pulley removal tool keeps the crank pulley still, allowing users to easily loosen or tighten the crank pulley bolt in most Honda or Acura engines.

Can a crank pulley be removed from an Acura?

If you have a 90s to early 2000s Honda/Acura, and you perform your own timing belt service, and you don’t have a powerful impact gun, then this is a must for your toolbox. This tool allows you to remove the crank pulley bolt that holds down the crank pulley on many Honda/Acura models.

How to remove a crankshaft pulley no power or air tools needed?

How to remove a crankshaft pulley, no power or air tools needed. DIY car repair with Scotty Kilmer, an auto mechanic for the last 42 years. 1. Bluetooth Scan Tool: http://amzn.to/2nfvmaD 2. Cheap Scan Tool: https://amzn.to/2D8Tvae 3. Professional Socket Set: http://amzn.to/2Bzmccg 4. Wrench Set: http://amzn.to/2kmBaOU 5.

How do you unbolt a crank pulley with an impact gun?

If you’re lucky, you’ll be able to remove the bolt on this pulley by using just an impact gun. Attach a 17mm socket and attempt to unbolt the crank pulley bolt. In order for this to work, you’ll need an impact gun with more than 600 lb/ft of breakaway torque. If you have one handy, try it out.

Can a crankshaft seal be replaced on a Honda Civic?

Also, the front crankshaft seal can be prone to leaking if it’s old or if it has been reused at any point. As much as a hassle this might be, the truth is it can be done at home as long as the right tools are used.

What is the pulley removal tool on a Honda?

Please make sure that you are posting in the form of a question. Please enter a question. The Powerbuilt 648796 50-millimeter Honda crankcase pulley removal tool keeps the crank pulley still, allowing users to easily loosen or tighten the crank pulley bolt in most Honda or Acura engines.

What’s the best way to loosen a crankshaft pulley?

If hook does not reach your desired spot, turn the crankshaft clockwise to give yourself some more room. See first pic. – Using the ratcheting wrench and the socket, turn the crankshaft pulley bolt counterclockwise (loosening) as far as you can go. There should be some good tension on the rope by now; it should not slip on the pulley.

What kind of pulley tool does Honda use?

The Powerbuilt 648796 50-millimeter Honda crankcase pulley removal tool keeps the crank pulley still, allowing users to easily loosen or tighten the crank pulley bolt in most Honda or Acura engines.

How do you tighten a crankshaft pulley bolt?

– Take the tie-down rope and wrap it around the crankshaft pulley as tight as you can in a clockwise direction. My pulley has 3 pulleys so I used the middle pulley. Tie-down should make about 4 or 5 loops around pulley.

How many loops around a crankshaft pulley bolt?

Tie-down should make about 4 or 5 loops around pulley. – Find a spot on the frame of the car that has a hole that the hood end can fit in. Be very sure this is on the frame and not some flimsy piece otherwise you can cause serious damage to your car and/or yourself.

Why did the pulley come off my Honda engine?

Secondly this gen Honda engine spins anticlockwise – if the bolt is loose it will work itself loose. The only way to tighten this bolt is to make a tool with a huge nut – something like 50 mm – it should perfectly engage the pulley hex cut that is cast into it.

What should I do if my crankshaft pulley comes off?

A long rod should be welded to the nut and the pulley is then held stationary as the main pulley bolt is tightened. No other way around it. If your woodruff keyway is damaged in the crankshaft – you need an excellent machinist to remake this – dont let him weld on the shaft, ask for him to make a proper and larger woodruff key

When does an idler pulley need to be replaced?

Most engines use one idler pulley, and one tensioner pulley, though some designs do use more than one idler. Over time, idler pulleys will eventually wear out and need to be replaced. Usually a bad or failing idler pulley will produce a few symptoms that can notify the driver of an issue. 1. Visibly worn pulleys

How big is the timing belt on a Honda Civic?

The timing belt on my JDM 1999 Civic (D15B Engine) is due for replacement. My car uses a 103 tooth, 24mm wide belt. I purchased a Gates 5409XS Belt off Amazon. 1. Handbrake Engaged and rear wheels chocked. 2. Safety Stand to support the front of the car.

What’s the orange ring on the crankshaft seal?

The orange-red rubber ring is the crankshaft seal. When you’re done with the crankshaft seal, finish installing the timing belt. After that, re-install the crankshaft pulley. Make sure to re-tighten the bolt to the specifications in the manual.

What kind of timing belt does a Honda Civic have?

Honda Civic Model Year Engine Belt / Chain 1995, 1996, 1997, 1998, 1999, 2000 1.3 L D13B4 I4 timing belt 1.4 L D14A3/A4/A7/A8 I4 timing belt 1.5 L D15Z4 I4 timing belt

Is there a way to loosen the crankcase pulley?

A simple way to hold the crankcase pulley so that you can loosen or tighten it. No expensive hard to find tools required, just a chain and breaker bar. Category Autos & Vehicles Show moreShow less Loading… AutoplayWhen autoplay is enabled, a suggested video will automatically play next. Up next

Is it possible to remove a crankshaft pulley bolt?

If you are trying to remove crankshaft pulley bolt we will show you how we do it and it works every time so far. It is very important not to turn the engine counter clockwise on most modern vehicles because they have complicated timing chains or belts and variable valve timing.

What can I do about a bad crankshaft pulley?

Remove crankshaft pulley bolt (usually using high torque impact wrench and pulley holder) The labor cost and price of a crankshaft pulley/harmonic balancer part may vary, depend on make, model and year of the car. If you decided to buy aftermarket product for harmonic balancer, I recommended you to buy Dorman harmonic balancer.

How is the crankshaft pulley attached to the engine?

The camshaft and crankshaft pulleys are directly attached to the engine (camshaft and crankshaft) and will only rotate if the engine is running or manually rotating the engine by placing a socket and breaker bar to the crankshaft pulley bolt.

How to remove a crankshaft pulley in your car?

Crankshaft pulley removal. How to remove a crankshaft pulley in your car DIY with Scotty Kilmer. How to use crankshaft pulley tool. How to remove a crankshaft pulley, no power or air tools needed. DIY car repair with Scotty Kilmer, an auto mechanic for the last 42 years. 1. Bluetooth Scan Tool: http://amzn.to/2nfvmaD 2.

What to do if your crankshaft is misaligned on Honda Odyssey?

Once you have the belt in place, put the left side tensioner pulley on and when you’re sure it’s lined up properly, pull the pin on the tensioner. The belt should be very tight on the right side tensioner and the water pump pulley with everything lined up, before pulling the pin on the tensioner.

Can a crankshaft sprocket break in a Honda Odyssey?

Going slow is the key. They’ll move OK with the timing belt off but once you have to move them and the crankshaft at the same time they can break loose and then you have to stop and retorque them. yeah I will be careful with the camshaft sprocket. It’s 14 years old and I just bought this van.

How do you replace the pulley on a Honda Civic?

Attach a long breaker bar to the “handle” end of the tool. It should be angled downward against the ground as a brace. Next, attach a 17mm socket to a long extension, and attach it to the crank pulley bolt through the center of the tool. Then, using another large breaker bar, crank on the pulley bolt counterclockwise.

How can you tell if a Honda Civic is dying?

Most of the time you can tell it’s dying by a constant squeal from the front of the motor that rises and drops with engine’s rpm. Also, the front crankshaft seal can be prone to leaking if it’s old or if it has been reused at any point. As much as a hassle this might be, the truth is it can be done at home as long as the right tools are used.

Where are the timing marks on a timing belt?

(2a) Find the timing marks on the flywheel and cam, and set them both to TDC. (2b) The flywheel pulley TDC mark is accessible through a hole in the bellhousing. (2c) The camshaft TDC is easy to find — especially if you add white paint as we did.

What does the timing belt do on an OHC engine?

The timing belt (or chain) is the sole component that keeps the camshaft (make that camshafts on a DOHC or V-type OHC engine) and crankshaft in sync.

Where are the timing marks on a camshaft?

How can I change the crankshaft seal on my laptop?

If you intend on changing the crankshaft seal after this, go ahead and heat the bolt with a torch for a bit before attacking it with the impact gun. It should come off more easily at the risk of potentially damaging the crankshaft seal. If playback doesn’t begin shortly, try restarting your device.

Can a crank pulley be turned by hand?

The only pulley you can’t turn by hand is the crank-pulley itself. The tensioner pulley itself might be bad. You would feel bad bearings inside as you turn the pulley – this one should spin easily. Any roughness or looseness indicates a problem.

How is the crankshaft pulley connected to the engine?

There is one mechanical system called a crankshaft pulley which helps distribute this engine power to other systems. The crankshaft pulley is connected to the crankshaft, which is a device that transforms the pistons’ linear motion into rotational motion.

How much does it cost to replace a crankshaft pulley?

Replacement Cost. The cost to replace a bad crankshaft pulley is anywhere from $350 to $400. The cost of labor is around $150 to $180 and the cost of parts is around $200 to $220. It is not the most expensive replacement job, but it is not too cheap either.

How to change front brake pads Honda Civic 1994?

If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. Hello and Welcome to my channel, Ive got over 20 Years Experience Fixing Modifying, Restoring Cars.

How big is the crank bolt on a Honda?

You are dealing with a 19mm bolt, which is called the “Crank Bolt”. This holds the harmonic balancer to the crank shaft. It is threaded opposite of the rotation of the engine, so this bastard is tighter than….well. It will take a load of leverage to break it loose. Once broken for the first time, you will hear a very loud pop.

What do you need to take harmonic balancer off Honda?

You will need (2) 1/2″ breaker bars, several extensions to get this out of the wheel well, a jack stand, and some bricks. Once you get the bolt off, keep a very close eye on where the “Woodruff Key” is, as it will fall when taking off the harmonic balancer. This tiny, nickel sized, piece keeps the balancer and crank shaft spinning together.

Why do I need to replace my timing belt?

If the crankshaft bolt is not tightened to specs it will back out. I have seen them go so far as to fall off, followed by the crank pulley and shredding the drive belts. These repairs only required changing exterior components. I can think of absolutely no reason for replacement of the timing belt again, the crank gear, or the timing covers.

Can you change the timing belt on a Honda Civic?

The timing belt on the Honda Civic turns the engine with the camshaft and crankshaft. If the timing belt needs replacing and you choose to do this yourself, consult with your mechanic before you begin. Changing a timing belt is a very difficult and precise operation that should be done by a professional if at all possible.

How do you remove drive belts from Honda Civic?

Remove the drive belts by loosening the mounting bolt nut for each drive belt’s main component, such as the alternator and power steering pump, with a wrench, turning the adjuster bolt to loosen the belt’s tension then slipping the belt off the pulleys. The power steering belt will come off first.

How do you remove the timing belt cover?

Unbolt and remove the lower timing belt cover. Detach the crankshaft position sensor by disconnecting its electrical connector and mounting bolt. Loosen the tensioner bolt for the timing belt with a ratchet or breaker bar, push on the tensioner to release the belt tension, retighten the bolt then slip it off the belt.

How do you replace a crankshaft pulley bolt?

I used a 2” (OD) piece of pvc to push the seal on. 2) Re-mount the crankshaft pulley. Line up the key slot with the key in the crankshaft and seat the pulley. 3) Install a new crank shaft pulley bolt and torque to 74 foot pounds plus and additional 75 degrees of rotation.

How to replace an automotive engine front crankshaft seal?

1. Disconnect the battery Anytime you are working on the engine front there is the potential of creating short circuit if you touch a wrench or any metal piece from battery power to ground. To prevent this remove the negative cable of the battery to stop the electrical power to the car. 2. Remove the Serpentine Belt

What causes the seal on the crankcase to loose?

As in with any engine seal heat and engine vibration can cause the seal to become hard and loose its sealing ability which will allow residual engine crankcase pressure to force oil past the seal and out from the engine.

Navigation