What are the symptoms of a bad blower motor relay?

3. Melted relay. Another more serious symptom of a problem with the blower motor relay is a burned or melted relay. Relays are exposed to high current loads and can sometimes get hot when they develop problems.

Why does my GM blower motor resistor keep failing?

In some cases, the heat is so high that it melts the connector. This is common on late model GM vehicles. If you discover a melted connector, do NOT attempt repair. Purchase an upgraded pigtail and splice it into the harness along with a new blower motor resistor.

What causes a fuse to blow on a blower motor?

If the blower motor relay develops any sort of problem that hinders its ability to properly limit and distribute power, it may cause the blower motor fuse to blow. Any sort of electrical spikes or excessive current from a bad relay will blow the fuse and cut power in order to protect the system.

Where does the power go in a blower motor?

For each higher speed, power flows through one less resistor. Some car makers run blower motor power through the fan speed switch first, then through the blower motor resistor and then to the blower motor and ground. Other car makers reverse that and run power to the blower motor first and terminate ground at the blower fan speed switch.

How much does a GMC Sonoma blower motor cost?

The best part is, our GMC Sonoma Blower Motor products start from as little as $26.99. When it comes to your GMC Sonoma, you want parts and products from only trusted brands. Here at Advance Auto Parts, we work with only top reliable Blower Motor product and part brands so you can shop with complete confidence.

What causes a bad or failing blower motor relay?

Blown fuses. One of the first symptoms of a bad or failing AC blower motor relay is a blown AC blower motor relay circuit fuse. If the blower motor relay develops any sort of problem that hinders its ability to properly limit and distribute power, it may cause the blower motor fuse to blow. Any sort of electrical spikes or excessive current…

Where is the blower control switch on the dashboard?

The blower control switch on the dashboard controls the circuit flow of the blower motor to adjust the voltage from low, to medium, to medium-high, to high. When on high, the circuit bypasses the blower resistor.

Where is the fan blower motor on my AC?

All fuses good all relays good. The fan blower for your ac/heater is located under the glovebox. Take your hand and smack the fan blower motor a few times. That’s all it took for for mine to start working again. It’s been working for over 6 month’s now!

What should I do if my blower wont shut off?

If the blower stops with either of these steps, the problem is in the HVAC control module. However, if the blower continues to run at high speed with either of those tests, replace the blower motor control processor. Just as an FYI, the retail price of the blower motor control processor is $280.34.

How do you disconnect a blower motor?

Turn the key in the OFF position. 2. Reconnect the blower motor speed control that you disconnect in the last step. 3. Disconnect the DATC/EATC module, connector C228a (see below). 4. Disconnect the blower motor relay (look in your manual, but I believe it’s relay 6 in the fuse box). 5.

Why does my Ford Expedition blower motor keep going?

My Ford vehicle decided to set the blower motor on HIGH no matter what. If I put my climate control to OFF, the blower motor keeps going. The fan control no longer works. The only way I can stop the fan is if I turn the vehicle off, then press OFF then restart the vehicle.

How much does it cost to replace a blower motor?

However, if the blower continues to run at high speed with either of those tests, replace the blower motor control processor. Just as an FYI, the retail price of the blower motor control processor is $280.34. There are a few places online that rebuild these puppies.

Why is my blower not working on my Jeep Wrangler?

Ensure this high standard is maintained by upgrading your Jeep Wrangler A/C blower motor with one from AutoZone’s high-quality array. A problem with your blower motor is often indicated by a fan that functions at high speeds but not in some lower speeds. This is sometimes a sign of a faulty resistor.

How much does a Jeep Wrangler heater blower motor cost?

Shop AutoZone for Jeep Wrangler A/C Heater Blower Motor. 10% OFF $75. Use Code: DIYSAVE10 Online Ship-to-Home Orders Only

What causes a Jeep Wrangler heater to overheat?

This is sometimes a sign of a faulty resistor. In certain cases the motor rotation’s mechanical resistance leads to extreme current that overheats and damages the blower motor resistor. AutoZone has several top-notch HVAC components, so you’re sure to find the right heater blower motor for Jeep Wrangler during your next in-store visit.

What to do if your Jeep blower fails?

If you look up in the passengers foot well, you can see the resistor and besides it the blower motor. The motor is fixed with 3 screws. Just wiggle all visible wires and see what happens. If the problem is inside the AC control panel, then there is most probably not much to do then replacing the panel.

What to do if your AC blower is not working?

Disconnect cables to motor and resistor. Remove hose from motor, it should just pull off with little effort. Unscrew motor and resistor. Screw new motor and resistor in. Connect hose to motor. Connect cables to motor and resistor. Turn on car and test AC. Thanks for watching! Loading…

Where is the blower connector on a jeep?

The blower motor sits right next to the resistor or controller (resistor is for manual AC, controller is for automatic AC system), so the connector can be found on the blower motor itself. Since the state of the blower changes after switching ignition off/on, the problem can be inside the AC control panel.

What happens if you have a bad blower motor?

The blower motor is the component responsible for pushing air through the vents of your vehicle’s heating and air conditioning systems. Without it, the AC system will not be able to circulate any heated or cooled air.

When does a blower motor start to fail?

In most cases, they start to fail by making a high pitched squeal or screeching noise that indicates the bearing is failing. The squealing noise happens most often in the winter during cold startups and may disappear as the motor heats up.

Where can I buy a blower motor in India?

More Shop No. 38, Shiv Darshan Shopping Complex, Off L. T. Road, Old MHB Colony, Borivali West,Mumbai, Maharashtra, India Ambala Cantt, India More Building No 80, Hsiidc Industrial Estate,Ambala Cantt, Haryana, India

How does a high speed blower motor work?

In the highest fan speed state, the blower resistor is bypassed completely and the fan is effectively connected directly to the car’s battery, allowing maximum current to be supplied to the blower motor.

Why is my blower motor only working at high speed?

The first thing that needs to be determined is the type of noise that is present and the possible sources. Rattling or knocking noises while… The blower motor only working on high speed is a common symptom of a failing blower motor resistor; but the fact the radio stopped working at the same time is unusual.

Where is the blower motor located on a car?

Your blower motor is typically located on the passenger side of the vehicle under the dash. Check for melting on the blower motor resistor or its plug. If they don’t appear to be damaged, the blower motor itself may need to be replaced. If the blower motor, resistor, or plug need to be replaced, O’Reilly Auto Parts has the parts you need.

Why is the resistor not working on my blower?

Hi There, The resistor is what controls the speed of the blower motor, not the relay. The blower motor relay supplies power to this motor when you turn the switch to “on” that can sometimes fail. When this happens, you may notice that you will not feel anything blowing out of the vents at all.

Why is my a / C blower making a loud noise?

Took my car in a few days ago for regular service, oil change, etc. and asked them to look into the a/c blower noise.

Where is the fan blower on a BMW?

It did make a noise far worse than that in the winter and then once it was warmer outside it went away and hasn’t come back yet. Either way it’s easy to replace the blower motor or clear the leaves out, it on the passenger side under the fuse box near the windshield.

What does it mean if your blower motor is not working?

Average rating from 849 customers who received a AC is not working Inspection. The blower motor resistor is an electrical component that is a part of the vehicle’s heating and air conditioning system. It is responsible for controlling the blower motor’s fan speed.

Why does my blower make a screeching noise?

If the screeching noise is still happening from your blower motor, either the noise is coming from a different part of the motor, in which case I’m little help, or you just haven’t gotten the bearing loosened from the motor shaft. If the later is the case, read on. If not, you may want to get yourself a new blower motor.

How can I get my GM blower motor to stop squeaking?

Spin the fan half a turn and spray a little more WD-40 to get the other side. Give it a few minutes to work in while spinning the fan a few times. Now you should be able to spin the fan without the motor making any noise.

How can I tell if my blower motor resistor is faulty?

Another symptom of a faulty blower motor resistor is no air from the vehicle’s vents at all. Power to the blower motor is fed through the blower motor resistor, so if it fails or has any issues power can be cut off to the motor.

How does a 3 speed blower motor work?

Older style blower motor resistor with exposed resistor elements. The blower motor resistor is what’s responsible for giving you three blower speeds. The resistor block contains three different high resistance coils. Think of these coils like a filament in a light bulb.

Why does my blower only work on high speed?

If your blower only operates on its highest speed, chances are you have the series type of blower motor resistor. This is the most common failure mode. To repair the problem, simply replace the resistor block.

Any sort of electrical spikes or excessive current from a bad relay will blow the fuse and cut power in order to protect the system. 3. Melted relay Another more serious symptom of a problem with the blower motor relay is a burned or melted relay. Relays are exposed to high current loads and can sometimes get hot when they develop problems.

When do you need to replace a blower motor?

Check for melting on the blower motor resistor or its plug. If they don’t appear to be damaged, the blower motor itself may need to be replaced. If the blower motor, resistor, or plug need to be replaced, O’Reilly Auto Parts has the parts you need.

How does a blower motor work in a HVAC system?

Your blower motor moves air through your HVAC system. Air passing over your A/C evaporator or heater core provides cooled or heated air to your vents. If there’s no air from your vents, your blower motor, blower motor resistor, or a connector may be at fault.

What causes a Mercedes Benz blower motor to fail?

The HVAC blower motor may fail. This is commonly caused by water entry through the cabin air filter areas during heavy rain or snow. Failed blower motors should be replaced. Our technicians tell us there is no special fix for this issue at this time. The average cost for a Mercedes-Benz S550 Blower Motor Replacement is between $735 -$755.

How much does it cost to replace Mercedes blower?

The average cost for a Mercedes-Benz S550 Blower Motor Replacement is between $735 -$755. Learn More Good news! We found 32 RepairPal Certified shops near you. Here’s a few you can book directly with. Air Conditioner does not work or blow.

Where is the regulator on a Mercedes fan blower?

The Mercedes Benz fan blower motor regulator is a series of resisters in a printed circuit board about 2-inches square located right next to the blower motor.

Why is my blower motor not coming on?

With the back wire hooked up I ran a jumper directly to the battery pos and attached it the purple wire terminal on the motor. The motor did not come on. So either my motor is dead shorted or something has gummed up the brushes or they are worn out.

How many volts does a blower motor have?

At low is might have 5V, M1 7 ish, and M2 9 ish volts. (note mine is not working and I think resistors are bad I get 11.9V on hi 11.73 v on all other speeds lo, m1, and m2. Anyone ever measure what voltages are normal to speeds ?

Where can I get a new blower motor resistor?

I replaced the blower motor resistor and the control unit with new parts from rockauto (ACDelco). I’ve checked the fuse in the dash fuse panel and it is good.

How is the speed of the blower motor controlled?

The blower resistor is connected in series to the blower fan motor. This means that the current running through the blower motor, and its’ speed is therefore controlled by the resistor value. The user chooses a fan speed by selecting a speed which then connects one of the resistors in the blower resistor pack.

I replaced the blower motor resistor and the control unit with new parts from rockauto (ACDelco). I’ve checked the fuse in the dash fuse panel and it is good.

Why is the blower motor not working on my car?

My car has an automatic transmission. Hi There, The resistor is what controls the speed of the blower motor, not the relay. The blower motor relay supplies power to this motor when you turn the switch to “on” that can sometimes fail. When this happens, you may notice that you will not feel anything blowing out of the vents at all.

What to do if heater blower won’t run?

If you have a 108, 109, 114 or 115 chassis you will have to remove the center console and dash to get to the motor. If you have a 107, 116, 123 or 126 Chassis access to the motor is quick. For the 201 and 124 chassis it takes a little more work as you have to remove the wiper and intake air vent assembly.

Why does my blower motor not come on?

You should be able to find this relay or sequencer by tracing the blower motor wires back to the relay or sequencer. If power is going into the sequencer or relay and not coming out when the 24 volts are applied then you have a relay or sequencer problem and the sequencer or relay will need to be replaced to get your blower running right again.

What to do if your blower motor switch is bad?

For this reason, if you suspect that your blower motor switch has a problem or fault, have the vehicle’s AC system diagnosed by a professional technician, such as one from YourMechanic. They will be able to replace the blower motor switch or make any other repairs that are appropriate.

Why do I need a variable speed blower motor?

A variable-speed motor, on the other hand, can operate at lower or higher speeds, which results in a more even temperature throughout your home and better energy efficiency. Similar to other components in an HVAC system, the blower motor will become more vulnerable to mechanical failures as it experiences more wear and tear over time.

Where is the blower motor on a car?

The blower motor is the electrical switch on the interior of a vehicle that allows the driver to control the vehicle’s heating and air conditioning system. It is usually built into the the same control panel that houses all of the AC system controls, and is labeled with numbers and symbols to indicate blower fan speed.

What causes a blower motor to not work?

If the blower motor resistors’ internal components fail it may cause the blower motor to malfunction, or not function at all on one or more of the settings. This can also be caused by a blower motor switch, so a proper diagnosis is highly recommended if you are uncertain of what the issue may be.

How do you troubleshoot a blower motor resistor?

This can be annoying, but troubleshooting is easy. If you start at the blower motor, and check resistance in the circuit, you will find the problem in no time. Power supplied from the fuse panel passes through the switch to the blower resistor assembly.

How can I tell if my blower speed switch is faulty?

Test for power at all the blower speeds by moving the blower speed switch through all positions. A faulty resistor loses power at different positions on the switch. High blower speed has direct power to the motor from the switch. If there is no power indicated on high blower speed, the problem is most likely the switch or the fuse.

Why is my blower motor not working properly?

As for the blower problem, if you find no fuses blown out and your system uses a variable speed control rather than several fixed speeds then the speed control module may possibly be damaged. It is a solid state unit the regulates the power to the blower motor. To see if the motor has a problem you could apply power directly to the motor. MarzK

What are the symptoms of a failed blower motor resistor?

Blower motor resistor problems. Problems with a blower motor resistor are common in many cars. The most common symptom of a failed blower motor resistor is when the heater fan only runs at high speed and doesn’t work at low speeds.

When does a blower motor need to be replaced?

CASE 2: The blower motor DID NOT run when you applied battery power and Ground with the jumper wires. This test result tells you that the blower motor is bad and needs to be replaced.

What’s the best way to test a blower motor?

The way we’re going to test the blower motor is by manually applying battery power and Ground with jumper wires or a power probe. NOTE: If you use a jumper wire, make your own fused jumper wire to apply battery power to the blower motor (as a safety precaution against shorting the jumper wire to ground).

What to do if your blower motor wont start?

You can test by testing with a voltmeter set to “Volt AC” between the high-speed blower wire (usually black) and the white neutral wire. If you are getting 120 volts to the motor and it is not starting then you have a blower motor problem and either need another new blower motor or a new blower motor run capacitor.

Why is the blower motor on my Nissan Altima not working?

Unfortunately the blower motor on the Altima is not working. The Blower motor LED lights light up to high speed but no fan. I am no where near the car ( My wife has it far away ) but I’m wondering if it is a fuse or the motor?

Why is the blower on my Nissan club not working?

Checked the two fuses, and they are both good. I can hear the AC compressor kick on if I lower the temp, but no air flow coming from the vents. Switching from defrost, floor, dash vents and no air flow. Manually adjusting the fan speed and still no air flow. It looks like there is a resistor plug that inserts into the blower assembly.

Why is my Nissan Sentra air conditioner not blowing cold?

Conclusion: A/C Not Blowing Cold Nissan Sentra Most of the time, when your Sentra’s air isn’t blowing cold enough, it is going to be a lack of refrigerant causing the problem. We recommend having a professional recharge your A/C if it does end up being a coolant issue. If you put too much coolant into the system, you can really do some damage.

What causes a blower motor to stop running?

Most blower motors ground through the case of the motor when it is screwed into place or by a small ground strap from the case to the body of the car. Over time, the ground connection can become corroded or loose, causing the motor to function intermittently. Lee Sallings is a freelance writer from Fort Worth, Texas.

Where is the fuse on a blower motor?

Locate the fuse for the blower motor in the owners/service manual. Test the fuse, with the ignition key on, using the 12-volt test light.

What causes a Nissan blower motor to run slower?

The auto AC regulates the fan control amp, which regulates the voltage to the blower motor. A low speed setting causes a lower voltage across the blower motor, which makes the motor operate slower. At maximum fan speed setting, the fan control amp allows nearly all 12v across the motor, which causes the fan to run faster.

Where is the blower relay on a Nissan Versa?

Blower relay is only used for speed 4 other 3 speeds run through the resistor unit. blower motor resistor block is actually in the air ducting near the blower motor.

What causes a blower motor to stop working?

In a situation where the motor doesn’t work on any speed, the most likely causes are: a blown power supply fuse, a bad motor ground connection, bad motor speed control module or a failed motor. On all systems, a failed blower motor is least likely. Blower motors generally don’t fail out of the clear blue.

Where does the ground go in a Honda blower motor?

The blower motor control module (Honda calls it Power Transistor) supplies the ground. The power transistor has 4 wires: two come from the climate control system control unit, one is the ground, one goes to the negative terminal of the blower motor.

How does a blower motor work in a car?

Carmakers use these three common wiring methods to supply power and ground to the blower motor in a manual system using a blower motor resistor. In one design, the car maker supplies battery power to the speed switch, which switches the power to the appropriate connection on the blower motor resistor.

How to test the blower motor and blower switch?

Basics Of Troubleshooting The Blower Control Resistor. TEST 1: Checking Continuity Of The Blower Resistor. TEST 2: Using A Jumper Wire To Bypass The Blower Resistor. Where To Buy The Blower Resistor And Save. Related Test Articles. The following tutorials on testing the blower motor and blower switch may come in handy:

Is the blower motor resistor OK in case 2?

CASE 2: All circuits tested had continuity where indicated in the test steps. This is good and is the correct and expected test result that tells you that the blower motor resistor is OK and not the cause of the blower motor speed problem. You can stope here if your blower motor resistor passed all of the continuity tests in this test section.

What should I do if my blower motor is not working?

If it’s good, refer to a wiring diagram for your vehicle and conduct these tests: Disconnect the electrical connector at the blower motor and jumper power and ground to the motor, bypassing all the speeds controls.

Why does my blower not work at high speeds?

Blower works on slow speeds, but not on high speed. Check for bad fuse or bad high speed relay. Swap the high speed relay with another relay with the same part number. Also, check the fuse for the control side of the high speed relay. Make sure the ground side of the high speed relay is working. Blower works on some speeds but not others

Why is my GM 3.8L blower not working?

If the blower motor in your 3.8L GM vehicle is stuck in only one speed (usually stuck in high) or no blower speeds work, then there’s a good chance that the blower control module is bad and behind the problem.

What do you need to know about the blower control module?

Basics Of Troubleshooting The Blower Control Module. The blower control module is a solid state device unlike the old style blower motor resistors that actually use resistors. It controls blower motor speed by varying the voltage it sends to the blower motor.

How can I tell if my blower motor resistor is bad?

A repair manual can tell you where its location is in your vehicle’s make and model. Inspect the resistor visually. Look for obvious signs of corrosion and burns from overheating.

Can a broken motor switch stop a blower?

A broken blower motor switch can also stop the blower from changing to certain speed settings. If your blower motor cannot change to certain speeds, check both the resistor and the switch on your dashboard. The most common failure points are the resistor and the motor itself.

Attach the clip lead of the test light to a good ground like a bolt screwed into metal, and touch the sharp probe end to the terminals on the fuse. An indication of power at both terminals of the fuse determines that the fuse is good. If one of the terminals has power and the other does not, the fuse is bad. Replace the fuse as needed.

How do you test the power of a blower motor?

Unplug the blower motor and test for power using the 12-volt test light in the same manner as explained in Step 1. Testing at the motor itself eliminates the possibility of confusion caused by complicated electronic blower controls found in Electronic Climate Control systems.

Why does my blower fan only work on one speed?

by Lee Sallings. The most common symptom of a faulty blower motor resistor is a blower fan that only works on one speed, usually high. This can be annoying, but troubleshooting is easy. If you start at the blower motor, and check resistance in the circuit, you will find the problem in no time.

Is the 10 Amp Fuse on my heater fan burned out?

The 10 amp fuse was not burned out. The blower motor resistor was a little rusty.I inspected and found no burned or melted wires anywhere , at the inside three way dash switch , at the blower motor and at the resistor.I know the air bag is tied into the same fuse , I must have replaced the fuse 12 times .

Why does my AC blower fan keep burning up?

1. The blower capacitor is weak causing the motor to overheat (a good tech would usually replace both the motor and the capacitor after a motor failure). 2. The motor is undersized. The HP and RPM of the motor must match the fan.

What should I do if my blower motor keeps burning up?

Certain Goodman units have a blower that requires an uncommon lower RPM. On this unit, the typical 1075 RPM 1/2 HP motor is not an acceptable replacement and will fail. Checking the motor amperage against the nameplate would expose this problem.

When do you need to replace the blower motor relay?

If the blower motor does not function, car fuses are blown, or relays are melting, you may have to replace the car blower motor relay. 1. Blower motor does not function 2. Blown fuses 3. Melted relay The blower motor relay is the electrical switch that is used to supply the power for the vehicle’s blower motor.

The blower motor is crucial to the proper functioning of your HVAC system. This video will show you how to properly diagnose your blower by using the multimeter to perform an AMP draw as well as replacing the blower motor relay. Loading…

How to replace blower motor, harness, and resistor?

Replacing the Blower Motor, Burned-out Harness, and Resistor: 2001 Dodge Dakota. DIY. How To. – YouTube If playback doesn’t begin shortly, try restarting your device.

How to test a Mercedes Benz fan blower motor regulator?

This is the blower motor resister, which controls the fan speeds. Disconnect the multi-wire connector from the blower motor resister next to the blower motor. Start the car and turn the air conditioning on. Test the connector for power at the terminals in the connector using the voltmeter. If there is power, reinstall the connector to the resister.

What are the symptoms of a bad heater motor resistor?

Symptoms of a Bad or Failing Heater Blower Motor Resistor. 1 1. Blower motor stuck on one speed. A common symptom of a faulty blower motor resistor is a blower motor that is stuck on one setting. The blower 2 2. Blower motor does not work on certain settings. 3 3. No air from the vehicle’s vents.

Which is a symptom of a faulty cooling fan?

The most obvious symptom of a faulty cooling fan system is the increase in warm or hot air in your cabin. A broken cooling fan system will affect the motors that run the blower causing them to supply less fresh air into the cabin of the car.

Can a faulty cooling fan cause a Volvo to overheat?

Failure of the cooling fan module to regulate the temperature inside the hood of your car can lead to the engine overheating. This can also happen when the cooling fan module is weak and therefore the fans work at a slower pace and are not able to regulate the heat. The faulty cooling fan module in your Volvo can simply be fixed by replacement.

Navigation