What does p0847 mean in Honda transmission?

P0847 HONDA Meaning The 3rd clutch transmission fluid pressure switch is installed in the hydraulic pressure circuit to the 3rd clutch. When hydraulic pressure is supplied to the 3rd clutch, the switch is turned ON. When hydraulic pressure is not supplied to the 3rd clutch, the switch is turned OFF.

What is p0847 Trans fluid pressure sensor switch B circuit low?

P0847 is typically an electrical circuit (TFPS sensor circuit) issue. This cannot be overlooked in the troubleshooting stage, especially when dealing with an intermittent problem. Troubleshooting steps may vary depending upon manufacturer, type of TFPS sensor and wire colors. Related trans fluid pressure sensor B circuit codes:

What is the diagnostic code for a Honda?

This generic powertrain/engine diagnostic trouble code typically applies to all OBD-II equipped vehicles including but not limited to Chevrolet, Acura, Honda, Saturn, Jeep, Toyota, etc.

How much does it cost to repair a Honda p0847?

The cost of diagnosing the P0847 HONDA code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.

What are the symptoms of a p0847 engine code?

Symptoms of a P0847 engine code may include: Vehicle starts off in 2nd or 3rd gear (limp in mode) Typically the causes for this code to set are: Short to ground in the signal circuit to the TFPS sensor – possible Failed TFPS Sensor / internally shorted – likely

This generic powertrain/engine diagnostic trouble code typically applies to all OBD-II equipped vehicles including but not limited to Chevrolet, Acura, Honda, Saturn, Jeep, Toyota, etc.

What does the Honda Accord p0700 transmission code mean?

P0700: Transmission Control System Malfunction. In the case of the P0700, it is a general code. This means that it should be accompanied by some other code that should tell you the specific problem. It is a OBDII code and not just a Honda specific code.

When does a Honda Accord get a trouble code?

The vehicles PCM (Powertrain Control Module) will throw the P0741 trouble code in the Accord if there is a difference that is greater than 200 rpm between the transmission input shaft and the torque converter speed. This is standard for any Honda vehicle made on or after the 1996 model year.

What does transmission code p0741 on Honda Accord mean?

P0741 will not affect the way that your Honda Accord’s engine performs at all. It is purely a transmission related code. Although, the engine response may “feel” different without the torque converter locking. It’ll be at a higher RPM, which means that it’ll feel “peppier” for lack of a better term.

How much does it cost to diagnose Honda code p0780?

The cost of diagnosing the P0780 HONDA code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour. When is the P0780 HONDA code detected?

How much does it cost to repair a Honda p0843?

The cost to diagnose the P0843 HONDA code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.

What is the code for Honda Pilot Oil pressure switch?

Thanks to this forum for all this advice when the CEL showed this code on my recently purchased 2011 Honda Pilot. Here’s my chance to give back for all the 2009-2011 Pilot owners with a flashing “D” and DTC 0847. The problem is purely electrical so that’s good news. The other good news is that Honda redesigned the part.

Is the p / n on a Honda P / NS?

The new part (28610-R36-004) has a black connector! I was able to order the part from Advance auto with a bunch of discounts here. Their p/n does NOT cross reference to any of the Honda p/ns, but when I got it in the mail, it was a genuine Honda part with the correct p/n.

Why is the oil pressure switch on my Honda Pilot not working?

This problem may also be caused by the switch wire being grounded to the chassis somewhere. Step 1: First off, I looked at the guide here on how to switch out the switch. It looked super easy, but ended up being really confusing me as Honda has redesigned the AT since 2003 models so the AT looks very different.

Navigation