How do you remove pulley from Honda engine?
Just slip the harmonic balancer back on (with the little woodruff key/wedge in place to hold it in position!) and then use the tool to rotate the engine. As an aside, don’t be alarmed if you let the engine rotate back clockwise (or if compression pushes it back) and the untensioned side of the belt, from cam to crank, has a fair bit of slack.
Can a crank pulley be removed from an Acura?
If you have a 90s to early 2000s Honda/Acura, and you perform your own timing belt service, and you don’t have a powerful impact gun, then this is a must for your toolbox. This tool allows you to remove the crank pulley bolt that holds down the crank pulley on many Honda/Acura models.
What’s the best tool to remove a crank pulley?
The Powerbuilt 50mm crank pulley tool is essential for removing the crank pulley on most Honda and Acura engines. It will save time, heartache, busted knuckles and endless frustration. Simple attach a 1/2″ drive socket extension and a long breaker or cheater bar and break the socket loose.
Just slip the harmonic balancer back on (with the little woodruff key/wedge in place to hold it in position!) and then use the tool to rotate the engine. As an aside, don’t be alarmed if you let the engine rotate back clockwise (or if compression pushes it back) and the untensioned side of the belt, from cam to crank, has a fair bit of slack.
How do you reset the oil pressure switch on a Honda?
1. Turn the ignition switch to the ON (II) position. 2. Press the select/reset knob repeatedly until the engine oil life indicator is displayed. 3. Press the select/reset knob for about 10 seconds. The engine oil life and the maintenance item code (s) will blink. 4. Press the select/reset knob for another five seconds.
What happens if your timing belt is off?
Here’s the thing, though – the period of time between “ownership” can be less than a second. If the timing is off, be it less than a second, there is nothing to stop the pistons and cylinders from colliding. This throws the rods off, and they start to poke holes in the engine block.
What kind of sprocket does Honda CRF230F use?
The change didn’t affect top speed much. The 230F uses the same front sprocket as the 88-95 XR250R. I bought a Sprocket Specialists 568 sprocket, but other brands will work as well ($12.96 from Chaparral). The Service Manual says to place the flat side of the sprocket facing out (the stepped side toward the engine).
Why is my Honda harmony making a ratchet noise?
When you turn the drive gear clockwise, it should move freely, and you should hear the ratcheting noise. When you turn it counterclockwise, the drive gear should grab the drift key and rotate the axle shaft. Reinstall the wheels and give her a test run.
What to do if your Honda Harmony has axle problems?
Clean any debris and dirt off the shaft and make sure there are no burrs on the axle shaft. If there are, lightly file them down. Grease the shaft and the key so all parts move freely. Reinstall the drive gear in the proper direction and reinstall the snap ring.
How big is the front sprocket on a Honda XL250?
Replaces OEM # 93500-04055-4J ISO Std. Pitch – Steel Plated Size: 4 x 55mm Front Sprocket Lock Plate with 2 Lock Plate Bolts. It’s Always good to replace these when installing a new front sprocket.
How big is drain plug on Honda P / N 90471-px4-000?
The Honda P/N 90471-PX4-000 specifies an 18mm I.D., as is otherwise correctly specified in this vendor’s description. The actual dimensions of the shipped product were, however, incorrect and not safely serviceable with an 18mm drain plug.
When to replace Honda genuine OEM Crush washers?
Honda OEM Replacement crush washers. 5 pack. 18 millimeters. Designed to be single use only, and should be replaced whenever fluid is replaced. There was a problem filtering reviews right now.
How to replace clutch center nut on Honda XL175?
Replaces OEM # 90082-HA0-000 Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Inside diameter 24mm, use with 3/8″ driver. Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut.