How do you inspect a fire hose reel?
Fire hose reels require regular visual examination by a competent person. Also an annual flow rate test and a pressure test are required. The fire hose must be pressure tested every five years. The test details should be recorded on a service label attached to the reel.
How often should fire hose reels be checked?
Fire Hose Reels need to be tested every 6 months and certified every 12 months. They are tested in accordance with AS1851.
When should hoses be inspected?
Hose that is in service should be service tested at least annually. Hose held in storage for longer than 1 year shall be service tested before being placed into service. Service-testing of nozzles – Testing should be done at least as frequently as the hose to which it is attached.
How do you service a fire hose reel?
Fire Hose Reel Maintenance
- ∗ Completely run out the fire hose from its reel.
- ∗ Check the fire hose and reel are in good condition.
- ∗ Check that all the couplings and joints are water tight.
- ∗ Check the spray nozzle can be opened and adjusted easily.
- ∗ Test water flow rate, static pressure and dynamic pressure.
How do you pressure test a fire hose?
Visually inspect machine • Cap the discharges • Pressurize to 440psi • Turn off pump • Hold pressure for 3 minutes • If there leaks between the pump and the discharges, the testing machine needs to be retuned to Small Tools for repair.
What are types of fire hose reel?
They fall into two broad categories – manual and automatic. With a manual fire hose reel the water supply must be turned on and off using a tap; with an automatic hose reel pulling the hose off the reel, usually for less than two full turns, will turn the water on. Both types can be fixed or swinging.
Should fire hose reels only be used by fire officers?
Along with fire extinguishers hose reels are used as a “first attack” appliance used during the early stages of a fire and can be used by building owners, occupiers, tenants and the fire brigade. All staff and personnel should be trained in the safe and effective use of fire hose reels.
What do you look for when inspecting hoses?
Feel for soft or mushy spots. A good hose will have a firm yet pliant feel. Inspect for cracks, nicks, bulges usually while hot), or a collapsed section in the hose and oil contamination, or fraying near the connection points.
What is a hose inspection?
External Inspection- Hose Inspect cover for cuts, gouges, worn spots or any other condition that exposes the reinforcement. Inspect hose for 18” behind each coupling for any evidence of leaking, basketing, kinking, bulges, soft spots or cover cracking exposing the reinforcement.
Can I use a fire hose reel for cleaning?
Fire hose reels are intended for use against a fire only, and therefore should never be used for washing or cleaning purposes.
Can you remove a fire hose reel?
De-Commissioning and Removal Once the removal of hose reels has been recommended by a fire risk assessment or the Fire Authority, M-Fire can de-commission and remove them from your site.
What is hose testing?
With hydrostatic testing you fill up the hose with a medium, such as water, and take it to a pre-specified test pressure and hold it for a period of time. During this pressure phase the hose is monitored and inspected to make sure the hose can withstand the pressure.
What does a rollnrack fire hose roller do?
This industrial grade ROLLNRACK ® POWER ROLLER is a portable fire hose roller that self-propels around curves and down the length of the hose. This all-in-one tool makes for effortless hose draining and rolling while using the correct body mechanics and never lifting hose rolls.
How often does equipment need to be inspected?
At least every 12 months the equipment must be inspected by a qualified person in accordance with paragraph (d) of this section (each shift) except that the corrective action set forth in paragraphs (f) (4), (f) (5), and (f) (6) of this section must apply in place of the corrective action required by paragraphs (d) (2) and (d) (3) of this section.
What should be included in an Occupational Safety and Health inspection?
At a minimum the inspection must include all of the following: Control mechanisms for maladjustments interfering with proper operation. Control and drive mechanisms for apparent excessive wear of components and contamination by lubricants, water or other foreign matter.