Are there any common problems with Cummins ISX engines?

Are there any common problems with Cummins ISX engines?

No all CUMMINS ISX engines are going to present all this problems but at least they are going to have one of them. This common problems are going to be similar all CUMMINS ISX engines from 2008 and up and all manufacturs: Freightliner Kenworth Volvo Peterbilt international, etc,..

What can go wrong with a Cummins diesel engine?

What Can Go Wrong With Cummins Diesel Engines? 1 1. Engine Not Starting or Hard to Start. In some cases, diesel engines will flat-out refuse to start. When an engine experiences difficulties starting 2 2. Running Rough at a Lower RPM. 3 3. Lack of Power. 4 4. Black Smoke. 5 5. White Smoke.

What do I need to know about my Cummins Engine?

You’ll need to check for: Low fuel pressure: Fuel pressure is a frequently cited catalyst for engine starting and running issues. The best way to rule it out is to check if the fuel tank is sufficiently filled, then make sure the pump is delivering fuel and run diagnostics on the actual pressure.

Why does my Cummins ISX have a sliding collar?

Click to expand… If the one on the ISX is built like the HE351VE used on the 6.7L Cummins in the Ram trucks, it is a sliding collar that changes the geometry of the turbine housing. The soot can build up in the moving parts and the actuator can’t move it properly.

Where are the vanes on a Cummins ISX?

In the 2nd video, you can see the turbine housing. The vanes on the turbine wheel fit in the slots of the rotating collar in the turbine housing at the left. If those slots fill with soot, the that collar can stick as well. Everything can be cleaned, but the dealers pretty much just replace them under warranty.

What to do if your Cummins ECM fails?

Diesel ECM engineers are skilled and trained to remedy the failure of electronic components with your Cummins ECM. We have a 1-2 day turnaround to get you back on the road quickly and efficiently.

Why does my ISX truck won’t start?

I took the truck to my regular mechanic to have a full service done, and after they replaced all the fuel filters, it woudln’t start over their pit. (the primer pump was whirring away everytime i turned the key to the on position) Long story short, they diagnosed it as a bad high pressure pump.

What kind of coolant does a Cummins engine use?

My 20′ international LT X15 (Cummins) has been consuming alot of antifreeze in the winter season but has been preforming well under no leaking nor visible damage…I have 74k on the engine as of right now and it uses Red extended life OAT (organic fluid) antifreeze…please fill me in on this matter, ty kindly and Happy New Year!!

What kind of truck is the Kenworth T660?

2009 Kenworth T660 for sale 10spd eaton Cummins isx 450hp 18ft hard dump body with ditch gate Air mud flaps Electric tarp Double framed 75% tire thread all around Current mileage: 1,008,404… See More Details 2013 Kenworth T660, 720,000 miles 600 HP Cummins, 303,019 miles on overall.

Where can I buy a 2006 Cummins Engine?

2006 Cummins ISX used diesel engine for sale . 400 HP, CPL 8520 tested and inspected with warranty. Call or visit our website for more info. 2006 Cummins ISX used diesel engine for sale . 400 HP, CPL 8520 tested and inspected with warranty. Call or visit our website for more info. Sold By: BASKIN TRUCK SALES LLC. Sold By: BASKIN TRUCK SALES LLC.

What kind of engine does a Kenworth glider have?

0 Miles on Fresh Overhaul using Genuine Detroit Parts including Oil Pump, Injectors, Turbo and Head ~ 579k Original Miles ~ Pre ELOG Detroit 12.7 ~ 500 HP ~ 13 Speed ~ 86″ Studio ~ Only One Owner! See More Details

Do you need to remove DPF on Cummins ISX?

If you are not close to them, you would need to remove the DPF, and get the exact measurements. There are 3 different filters for a Cummins ISX. I kept the old filter, so if I ever sold the truck, I could simply reisntall the old filter, and just take it somewhere to have factory ECM settings put back in the truck.

Is it necessary to change out turbo on ISX?

All I had to do was reburn the ECM, and put in a fake DPF canister for back pressure on the turbo so it won’t overspool. It cost me $3,000 parts and labor. You can change out turbo, but not required.

Can a VGT turbo run on an ISX truck?

Fuel mileage increased, was able to pick from Pre-EGR engine horsepower ranges. Original ECM on truck, EGR valve and cooler still on truck, and can run VGT turbo. Truck looks factory OEM. Was visually inspected in California, and passed. Posted by a private member. Posted by a private member.

Can a worn camshaft cause an ISX to fail?

Apart from performance issues caused by a worn camshaft cluing you in to a camshaft problem, there aren’t any particular symptoms to watch for that indicate whether or not you have these rockers. This issue is usually found after a camshaft repair or overhaul, when the timing might be affected.

Why did Cummins change to single cam engine?

It soon replaced the N14, the other workhorse engine produced by Cummins. Throughout its production history, Cummins has made various changes to the engine in order to keep up with the increasing restrictions, changing from a dual-cam to a single-cam and adding a cooled EGR system to reduce NOx emissions.

Why are the rocker arms on my Cummins not working?

According to Cummins, there was a production of rocker arms that prevented proper oil flow, starving the components. These bad rocker arms stick and smack the camshaft, causing the lobes to flatten. You can fix this failure by replacing both the affected camshaft and the rockers.

Why is transmission not engaging on high side 7-9?

Not engaging on high side 7-9, I was told there are lines crossed. I have changed air dryer and governor. Lines switched around, and either I have correct air pressure and sleeper air bags and no shifter, or shifter and losing air pressure down to 60.

Where is the solenoid on a Volvo truck?

Leesburg, Fl. If its the early I-shift that Volvo used it could be several things. Since it shifts thru the first 5 gears. The most common problem would be the high/low range solenoid. This is mounted on the top of the trans right behind the shift control unit.

What’s the problem with my Volvo I-Shift?

If its the early I-shift that Volvo used it could be several things. Since it shifts thru the first 5 gears. The most common problem would be the high/low range solenoid. This is mounted on the top of the trans right behind the shift control unit. First suggestion before removing that solenoid.

Why does my Cummins mile not stay running?

My cummins ISX 832000 mile will not stay running it will start but then shut down. You can start it rate back up but it will shut down like you turned the key off. New filters & clean all posts on battery. was not having a problem when I parked the truck friday went out today to start it up and now I have this facing me.

What should I do if my Cummins Engine wont start?

The tech should have checked the cam position sensor, Fuel Rail pressure sensor, intake pressure sensor, Exhaust pressure sensor, EGR position sensor and the EGR differential pressure sensor by running the engine, unplugging each one and see if the fault returns when it is plugged back in.

Is there an issue with the 187 Cummins?

The only issue with 187 is for sensor supply #2 which includes the cam position sensor, not the engine position sensor. With the loss of the cam sensor the engine will derate, really shouldn’t shut down. With the loss of the cam sensor the ECM relies on the engine position sensor and vise versa.

What’s the serial number on a Cummins Peterbilt?

2011 Peterbilt; Cummins ISX engine. Husband stop to nap; woke up and tried to start engine; Engine light came on and no power. I do have serial … read more 2006 Peterbilt ISX trouble code 245….what caused this malfunction? 2006 Peterbilt ISX trouble code 245….what caused this malfunction? Fan is on full-time now. … read more

When did the Peterbilt ISX 600 come out?

Just got 2008 Peterbilt 386 with a Cummins ISX Signature 600 out of MHC Denver. After having two (2) sensors replaced – the pressure sensor & the TPS Assy (which was under warran … read more

How does Insite engine diagnostics software work for Cummins?

INSITE performs engine diagnostics and displays electronic engine information on your PC. With step-by-step diagnostics, built-in engine drawings and schematic diagrams, working with INSITE is easy. Using this software application will reduce troubleshooting time, errors and incorrect procedures and quickly get your vehicle back on the road again.

What kind of engine does Kustom truck use?

Kustom Truck offers complete packages including CAT, Cummins, and Detroit Diesel factory reman engines complete with an engine installation harness.

Where is the lift pump on a Cummins?

Click to expand… 04 peterbilt 379 as far as engine serial, where I’d that located? Drivers side of motor will have a tag top left with serial number. I think there’s a relay for the lift pump on the side of motor.

What does the ISX stand for in diesel engine?

It upheld its name because it had an innovative fuel system called the “Interact System.” The “IS” in ISX stands for “Interact System.” Since its launch, the ISX has been the core of Cummins’ diesel engine fleet. Not only has it advanced with quicker processing, but it has also increased fuel efficiency since its debut.

What kind of SCR does Cummins ISX cummings use?

The ventilated exhaust lowers the combustion chamber temperature. The ISX Cummings started featuring the selective catalytic reduction (SCR) system in 2006. It injects urea, which is an active element in diesel exhaust fluid (DEF), into the exhaust.

Is the Cummins X-15 a good engine?

Now, the problem children are the CM-2250, CM-2350, and the X-15, which there is not yet that much feedback on. The 2250-2350 are high compression motors, it does not like to be turned up, but can be tuned. Then we have the fuel system.

How to fix my Cummins no crank issue?

MY CUMMINS NO CRANK – NO START ISSUE FIXED WITH THIS!?!? – YouTube MY CUMMINS NO CRANK – NO START ISSUE FIXED WITH THIS!?!? If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.

What are the ISX 2350 no start codes?

I have an ISX 2350 that cranks, no start. Codes 559, 555, and 4691. I had just put injector sleeve retainers in this engine, changed the fuel filters before starting, and codes appeared. It will run if I start with ether, but will die sporadically while driving.

Is it common for a diesel engine to misfire?

The good news is that engine misfires are a common occurrence and not a symptom of something more serious that is wrong with the diesel engine. Each engine is different and for example Mack E-7 or E-Tech engines have a thicker gauge fuel line than say a Detroit Series 60 or a CAT 3406E.

What causes engine misfires on a Mack truck?

On a Mack engine the problem could be more with the injectors than the fuel line. It is important to check each engine component separately to rule out issues one by one. Start with the easiest fix and work your way up. If you still have engine misfires feel free to contact a diesel parts specialist for further assistance.

What kind of engine is a 2012 Kenworth?

I have 2012 Kenworth with a Cummins ISX 15 450. (Engine No 79554126). I’ve been having issue with power delivery. Truck seems to be doing fine when suddenly you feel the loss of power, if you take the foot out of the gas pedal kinds of breath and gets back to normal.

What kind of Cummins engine is for sale?

2009 Cummins ISX used diesel engine for sale. 500 HP. CPL 2733. Tested and inspected with warranty. Fits To: AUTOCAR, DODGE, FORD, FREIGHTLINER, INTERNATIONAL / 108SD, 114SD, 122SD, 1955, 2000, 200-33, 2110A, 220, 2200, 2275; 2008 Cummins ISX used diesel engine for sale .400 HP, CPL 2732, tested and inspected with warranty.

Who was the founder of Cummins Engine Company?

When you know the ins and outs of your engine system, you can better prepare your marine or generator applications to make functional repairs when necessary. Clessie Cummins founded Cummins Engines in 1919 and partnered with J. Irwin Miller, a knowledgeable man in business practices.

What kind of engine does a Peterbilt 386 have?

Only 278k Miles on Overhaul including Head, Pistons, Oil Pump and Water Pump using Genuine Detroit Parts ~ Detroit 12.7 ~ 500 HP ~ 10 Speed ~ Financing Available with Your Good Credit 2014 Peterbilt 386, Cummins ISX 450hp, Jake, Eaton Ultrashift, 12/38, Air Ride, 196″ WB, 3.42 Ratio, LP22.5, All Alums, A/S 5th, 80/80 Fuel Tanks, 221K miles.

What’s the most common problem with a Volvo truck?

The most common problem would be the high/low range splitter. Which is partially air controlled, partially electric controlled. right of the tail-shaft. There is a air metering solenoid in this system to control the air flow to the high/low range splitter.

How old is the motor on a Peterbilt truck?

2013 Peterbilt, Motor Rebuilt, Air Ride Suspension, Cummins 485 HP, Ready For Work, Call For More Details! Rebuilt Motor in October of 20 only 38,000 full 2 year warranty unlimited mileage warranty. All disc brakes, all new hubs and rotors and pads, everything has been gone through.

Where is the return line on a Cummins ISX?

SWITCH FUEL LINE AND RETURN LINE POSITIONS IN TANK (in case there was a problem with the pick up tube in tank, we put the return line on the pick up tube in the tank, and vice versa. These two pick up tubes are welded into the tank, and seem the same).

Is there a problem with my Cummins truck?

Zip, zero, none… The truck has been to the Cummins shop in Roanoke, VA THREE times for this issue. It never messes up when they have it. They’ve checked the codes and find nothing… It has been to two other shops, about two times each for this issue. We were just hoping that someone might get lucky and find the problem.

What are the fault codes for Cummins engines?

Cummins engines fault codes list Error code 111 Engine: ISF 2.8, ISF 3.8, ISB, QSB, QSC, ISL, QSL, ISM, QSM, ISX, QSX Error: ECM internal failure. Description: This DTC can only occur if there is a problem inside the ECM.

When does an ISX fault code become active?

The pressure in the intake manifold exceeded the maximum allowable value for a given engine rated power. This DTC becomes active when the pressure in the intake manifold exceeds the maximum allowable value for a given engine power rating. ISF 2.8, ISF 3.8, ISB, ISC, ISL, ISLe , ISDe , QSB 3.3

What causes a DTC on a Cummins Engine?

Possible causes for this DTC are damage to the camshaft position sensor, an open or short circuit in the circuit, or a fault in the power circuit. The engine speed signal from the crankshaft position sensor is not detected.

What kind of tires does a Volvo 670-67 have?


Are there any Volvo vnl64t670 trucks for sale?

Fleet truck for sale Well maintained truck with most of the maintenance done by the company. 571528 miles on the board, 10 speed Eaton fuller transmission, ISX15 450HP No Def, NO EGR.

What kind of engine does a Volvo vnl670 have?

2004 Volvo VNL670, 70″ Raised Roof Sleeper, Volvo motor, 465 H.P., 10 speed, Engine brake, Cruise Control, Cold A/C, Air Ride, Aluminum Wheels, Good Rubber, Tilt Steering, 2 to Choose From This beautiful Volvo VNL670 is ready to put to work.

When did Cummins start having problems with EGR?

For example, engines engineered before 2002 will experience more problems with EGR compared to modern types. In 2008, Cummins began noticing the SCR system experienced failing revolving parts, interfering with the engine’s horsepower. Clogged inlets came about in 2010 when recirculation was occurring, also affecting HP.

What kind of truck is a Cummins 379?

2007 PETERBILT, 379, Heavy Duty Trucks – Conventional Day Cab Trucks, Cummins ISX, Manual, 2007 Peterbilt 379 Day Cab White over Gray Interior VEHICLE… 2007 PETERBILT 379, 2 Available: Beautiful monsters, heavy duty: 2007 Peterbilts 379 Roll Off Trucks one has 314,000 miles and other has 334,000 miles…

What kind of truck is a 2007 Peterbilt?

2007 PETERBILT, 379, Heavy Duty Trucks – Conventional Day Cab Trucks, Cummins ISX, Manual, 2007 Peterbilt 379 Tandem Axle Day Cab, FRO-18210C 10-Speed… flat top sleeper, Caterpillar 550, VIN 1XP5DB9X570688634 *THIS ITEM IS TO BE SOLD AT AUCTION WITH STEFFES GROUP, INC. CLICK THE URL TO GO TO THE AUC…

Why does my ISX truck refuse to start?

The truck sat overnight and mosat of the day yesterday, and then around 3pm i went to start it and it did the same thing as it did over their lube pit. I pulled the fuel filters and found the fuel levels inside to be low.

How much did it cost to clean a 2009 Cummins ISX?

They had it for three days and charged me for 10 hours of labor, $500.00 for the DPF cleaning, a couple gaskets and a clamp, about $1,800.00 out the door. I left, parked for the night and the next morning, drove 180 miles to deliver a load.

How often does the fuel injector activate in an ISX engine?

Then, it’s distributed through the tubing to the rail system for storage under extreme pressures— about 35,000 PSI or higher. This version of the ISX relies on an engine control module (ECM) to monitor the timing and pressure. The ECM can activate each fuel injector up to five times per combustion cycle.

What kind of engine does a 2013 Kenworth T800 have?

2013 Kenworth T800 Cummins 500 open to 565 HP Automatic Transmission Eaton fuller 18 speed. 4.11 rears all heavy specs Fully loaded leather AC GPS Bluetooth Complete DEF System done last year Clutch done last year. Tires and brakes. Working everyday asphalt Very well maint…

What kind of engine does a Kenworth T660 have?

Clean, 2013 Kenworth T660 Day cab is looking to get back on the road! White in colour, powered by Paccar MX engine and 13 speed trans with 485HP. Freshly painted frame and comfort on the inside to enjoy your daily travels. Our used units are always ready to work before they le…

Can a Cummins engine be put in a truck?

I put a crate engine from Cummins ReCon at 800k miles. Yes it had a bad cam and fallower. Guy I’m leased to put a new Cummins engine in his 13 after the fuel pump took a dump and destroyed the engine at 340k miles.

How to become a Cummins ISX trucker fan?

Discussion in ‘ Peterbilt Forum ‘ started by Hshappy2, May 13, 2017 . Now it’s stay on!whats wrong ?? Every month 400 people find a job with the help of TruckersReport. Please Select… I Need CDL Training In CDL School Now CDL Grad, No Experience 1-5 Months 6-11 Months 1 Year 2 Years 3 Years 4 Years 5+ Years

What kind of truck is a 2007 Kenworth?

2007 KENWORTH, W900L, Heavy Duty Trucks – Logging Trucks, Cummins ISX, Manual, 2002 ASSEMBLED LOG TRAILER WITH 8′ 6″ BUNKS AND ELECT. SCALES, 550 Hors… You might like these other KENWORTH Trucks.

What kind of engine does a 2007 Kenworth T600 have?

2007 Kenworth T600, TRUCK, 2007 Kenworth T600, Cummins ISX 450HP Engine, 13 Speed Transmission, Air Brakes, Air Suspension, 50,000lb GVWR, Aluminum Wh… 2007 KENWORTH, T600, Heavy Duty Trucks – Conventional Trucks w/ Sleeper, , , Parts Sold Daily!Please Call to see if part is still available!Don’t see

Is the Cummin ISX in a 07 379?

It also is in an 07 379. Being that is a 500 it does not seem to be as prone to the Cam issues as the larger hp motors. Every month 400 people find a job with the help of TruckersReport. Please Select… I Need CDL Training In CDL School Now CDL Grad, No Experience 1-5 Months 6-11 Months 1 Year 2 Years 3 Years 4 Years 5+ Years